Bedienungsanleitung Be Cool Thunder Iso-Fix (Seite 16 von 32) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

768111

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

THUNDER iso-ﬁx

INSTALLATION TIPS

1) The THUNDER ISO-FIX shall be used with

isoﬁx anchors plus top tether for group I (9-

18kg child).

2) The THUNDER ISO-FIX must be used with

ISOFIX anchors (no top tether needed) at the

same time that with a 3-point seat belt for

group 2, 3 (15-36kg child).

3) The THUNDER ISO-FIX must be ﬁtted as

a forward-facing position in the rear seats of

vehicle.

Four positions of the car seat

The THUNDER can be used in four different

positions. (Fig. 1):

Pull the positioning handle under the front

of the seat forwards or backwards (feel the

spring underneath), then release the handle

on your required position while hearing a dis-

tinct click.

ISO- FIX Group 1

INSTALLATION

Installing method for Group I (9-18 kg)

a) Place the THUNDER ISO-FIX on the vehi-

cle’s seat.

b) Rotate the adjuster button in anti-clock

wise direction (F2-A) and pull the isoﬁx an-

chors out-wards as far as it goes, make sure it

can’t be pushed back (F2-B).

c) Push the car seat towards the back of ve-

hicle’s anchoring point (F3-A) and match the

isoﬁx anchors to the vehicle’s anchoring point

until hear a “click” (F3-B).

e) Rotate the adjuster button in anti-clock

wise direction (F4-A) and push the car seat to

the back of vehicle’s seat as much as possible

(F4-B).

f) Hook the top tether up and pull as tight as

possible (F7).

ISO- FIX Groups 2 /3

Installing method for Group II (15-25 kg) /

III (22-36 kg)

The installation method is for child within

Group II (15-25 kg) and Group III (22-36 kg).

a) Remove the harness system, including the

belt pads, central buckle and crotch strap.

b) Adjust the headrest by pulling the lifting

handle at your required position according to

your child’s height.

c) Place your child into the car seat.

d) Thread the vehicle’s shoulder belt from the

Group II belt guide slot (Fig. 14-a), or Group III

belt guide slot (Fig. 14-b), and thread the lap

belt through the belt guide (Fig. 14-c).

So the installation is completed (Fig. 14-d).

e) Joint the belts and buckle up.

Placing your child in the THUNDER car seat

Loosen the shoulder belts by pressing the

realease button and pull the shoulder belts

towards you.

Important: Do not pull on the belt pads when

doing so. (Fig. 8-9)

Press the red button to open the buckle. (Fig.

10)

Part the belts over the sides of the shell. (Fig.

11)

Place your child into the shell and make sure

that there are no toys or other hard objects in

the shell. (Fig. 12)

Match buckle tongue sections together and

insert them into the buckle. (Fig. 13)

f) Make sure the shoulder belts ﬁt your child

snugly by pulling the adjuster belt. (Fig. 14)

Note! After you have done the installation,

check it by trying to move it, it shouldn’t move

more than an inch side along the belt path,

if it does, tightens the straps or try installing

it again. The belts should never be twisted.

If you are unable to click the tongue sections

into the buckle, unlock the buckle by pressing

the red button and try again.

IM-1613.02 THUNDER isofix 30.7.15.indd 16 30/07/15 11:13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Be Cool Thunder Iso-Fix Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info