Bedienungsanleitung Be Cool Tornado i-Fix (Seite 22 von 52) (Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

768112

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

2 - INSTALLING WITH VEHICLE’S SEAT BELT

1. Place your child in the car seat and make sure they are sitting

well back.

2. Thread the vehicle’s seat belt through the belt guide under the

headrest and the belt guide under the armrest.

2.1. Pass the diagonal section of the seat belt through the belt

guide under the headrest.

2.2. Pass the lap section of the seat belt through the seat belt

guide under the armrest next to the seat belt buckle.

2.3. Ensure that no part of the seat belt has become twisted or

trapped and that the car seat’s fabric cover is not impeding the

movement or correct tting of the seat belt.

3 - INSTALLING THE CHILD CAR SEAT

3. Ensure that the diagonal belt lies gently on the child’s

shoulder and the lap belt is worn over the hips Tighten the

diagonal section of the seat belt by pulling it upwards until

there is no slack and the belt holds the child rmly in place.

4. To take the child out of the seat, simply unfasten the seat belt

and undo the shoulder belt guide.

4 - USE THE ISOFIX SYSTEM IF YOUR VEHICLE’S

SEAT HAS ADDITIONAL ISOFIX ANCHOR

If your vehicle is equipped with Isox anchor points, these should

be used to obtain a more stable installation.

These cars will have plastic elements that guide the seat’s Isox

anchors into their correct positions. If your vehicle does not have

these guide elements, you can use the plastic guides provided

with the car seat.

Caution: When the seats of your car are equipped with Isox

anchor points, install your car seat using your vehicle’s ISOFIX

anchor points ALWAYS and ONLY in combination with the car’s

safety belts. See the vehicle list.

Match the back rest hook to the rear side of base from lying

position to upright position, to make sure the back rest is fully

matched into the base.

1. Place the car seat in the appropriate position on the vehicle’s

seat, facing in the direction of travel.

2. Rotate the adjuster button in anti-clock wise direction, and

simultaneously pull the isox connectors outwards as far as it

goes, make sure it cannot be push backwards.

3. Position the car seat facing forwards on the vehicle seat with

ISOFIX points.

4. Match the ISOFIX connectors to the vehicle’s anchoring point

until hear a “click”.

5. Rotate the adjuster button in anti-clock wise direction, and

simultaneously push the seat against the vehicle to eliminate

the gap between car seat and vehicle’s seat.

ATTENTION! ISOFIX connectors are an additional tting system

for securing the car seat and not suitable for securing a child.

Child must always be secured by means of the car’s three-point

safety Belt.

IM 2013,01 TORNADO_IFIX ins OK.indd 22 19/6/18 19:24

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Be Cool Tornado i-Fix Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info