Bedienungsanleitung Be Cool Zero - 2021 (Seite 22 von 48) (Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

768118

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

2 If the seat belt is short:

a. In most vehicles, the height of the shoulder belt can be adjus-

ted, adjust it to the lowest position.

b. If the vehicle seat can be moved, move it backwards.

3. INSTALLING THE SEAT IN THE CAR

The ZERO safety seat must be installed FACING THE OPPOSITE

DIRECTION IN WHICH THE CAR IS TRAVELLING. Decide on the

seat after reading the “Choosing where to install the safety seat”

section.

To install the seat carefully follow the steps below:

3a.- Position the safety seat on the vehicle seat.

3b.- Pass the seat belt buckle over the baby’s feet and fasten it.

3c.- Insert the abdominal part of the seat belt through the slots (1)

on the sides of the frame.

3d.- The shoulder part of the vehicle seat belt should be passed

behind the safety seat.

3e.- Turn the handle (6) to the AUTO position, the furthest

forward. The full car symbol should

be displayed on the sides of the handle.

3f.- Tighten the car seat belt and fasten the locking clip (2). Make

sure that the safety seat is securely anchored by pulling it.

WARNING: For installing rear facing safety seats, the correct guides

for tting the seat belt are marked on the chassis in blue. DO NOT

use any guide that is not described in these instructions or any on

the baby carrier that are not coloured blue.

If the safety seat is installed with the ISOx base (optional), follow

the instructions on the base.

4. PUTTING THE BABY INTO THE SAFETY SEAT

4a.- Loosen the harness by puling on the shoulder straps while

pressing the tightener button (8).

4b.-Undo the clasp.

4c.- Put the baby in the safety seat, making sure that they are

sitting back in it and that their back is straight. Join the top

ends of the clasps.

4d.-Insert them in the fastener and press until you hear a ZERO.

4e.-Tighten the shoulder straps and pull the tightener strap (7).

5. INSTALLING ZERO IN A PUSHCHAIR

Your ZERO carrycot can be fastened to any BE COOL chassis that

has the PRO-FIX system.

5a.- To fasten the safety seat to a chassis, insert the connections

in the cavities on the chassis and press until you hear a ZERO.

5b.- To release the ZERO from the chassis, pull both buttons on

the sides of the handle (9) and lift the seat

WARNING

Never leave your baby on their own.

Any changes or additions to the ZERO without the correct

authorisation from BE COOL may seriously affect the safety of the

restraining system.

Read these instructions carefully before use and keep them for

future reference. Your child’s safety may be affected if you do not

follow these instructions.

This safety device cannot be used without its cover, or replaced

with one that is not the original, as it is an integral part of the

system’s safety features.

Never add a mattress pad, pillow or extra padding to make it more

comfortable for the child as this will alter the safety characteristics

of the system.

Check that the seat has been positioned correctly.

Make sure that the seat belt is not trapped between the folding

seats or doors.

IM 1631,03 ZERO ins OK.indd 22 19/4/21 20:10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Be Cool Zero - 2021 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info