Bedienungsanleitung BeamZ 150.382 - Fuze 75S Spot (Seite 6 von 38) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

765568

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

DMX512 CONTROL

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first fixture in a DMX chain.

Always connect the output of one unit with the input of the next fixture until all fixtures are connected.

Caution: At the last fixture, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor

between signal (-) and signal (+) and connect it to the DMX output of the last fixture in the line.

RF REMOTE CONTROL

1. Select the type fixture you will control:

- Press repeatedly 3 times on button “Spot” to activate Fuze Spot Series

- Press repeatedly 3 times on button “Beam” to activate Beam Spot Series

- Press repeatedly 3 times on button “Wash” to activate Wash Spot Series

2. Press the button “Dimmer” to adjust brightness. Press directly on the button “+” or “-“ for desired settings.

3. Press the button “Strobe” to turn on/off the strobe effect. Press directly on the button “+” or “-“ for

desired settings.

4. Press the button ” ” to adjust the speed of sound program or adjust the sensitivity of sound control.

5. Press the button ” ” to adjust the speed of chase or adjust the sensitivity of voice control.

6. Press the button “1-9” to select one of the auto or sound activated programs.

7. Press the button “ ” to reset all.

8. Press the button “DMX” to select control via wired DMX signal.

Tips:

1. When activated RF function, the lamp will not control by DMX signal and the lamp is in the RF control

state. Each remote controller can only control a series of fixtures at the same time.

2. When Wash series opens “Dimmer” and “Strobe, it needs to press the number button to brighten the corresponding colour. In this mode, the

number button can only switch the colour wheel, but not the corresponding key colour for Spot and Beam series.

3. To turn off RF function, there are the following methods:

a. Select the signal input mode needed, “DMX’ can exit RF function.

b. Switch to other series of fixture “Spot”, “Beam”, “Wash”.

c. Press the menu button of the display panel.

The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery

from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote

control. Otherwise operation of the remote control is not possible.

If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote

control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For

operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the

button cell shows upwards in the support.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 150.382 - Fuze 75S Spot Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info