Bedienungsanleitung BeamZ 150.624 COB100UV (Seite 5 von 24) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766956

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

DISPLAY

The control board offer several features: you can simple set the starting address,

run the pre-programmed program or make a reset. The main menu is accessed

by pressing the Mode-button, browse through the submenu by pressing Up or

Down.

Press the Enter-button in order to select the desired menu.

You can change the selection by pressing Up or Down. Confirm every selection

by pressing the Enter-button.

You can leave every mode by pressing the Mode-button. The functions provided

are described later in this manual.

DMX-512 CONNECTION

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the

first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.

5-pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be

implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used.

The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conducto

3-Pin XLR Female (Out) 5-Pin XLR Male (In)

Ground/Shield Pin 1 Pin 1

Data Compliment (- signal) Pin 2 Pin 2

Data True (+ signal) Pin 3 Pin 3

Not Used Pin 4 – Do Not Use

Not Used Pin 5

–

Do Not Use

At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between signal (-) and signal (+) into a 3-pin

XLR connector and plug this into the DMX output of the last fixture in the chain.

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding

can cause greater accumulation of dirt on the unit’s optics.

 Make sure the area below the installation place is free from unwanted persons during servicing.

 Housings, fixations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation.

 The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is

detected.

 In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned

monthly.

 The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.

 Clean with soft cloth using normal glass cleaning fluid.

 Always dry the parts carefully.

 Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.



ATTENTION: We stron

recommend internal cleanin

to be carried out b

ualified worker!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 150.624 COB100UV Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info