Bedienungsanleitung BeamZ 150.691 Star-Color 270Z (Seite 7 von 38) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766839

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Fixtures with protection class IP65 are dust-tight and completely protected against contact (first code number). They are also protected against splash

water from any angle (second code digit). That is why this fixture can also be used out‐ doors. Events fixtures are generally only designed for temporary

use however (event lighting) and not for permanent use outdoors. The specified protection class does not make a statement about the weather

resistance of the fixtures (resistance to changing ambient conditions as well as against the effects of sunlight and UV rays). The seals and screw

connections of the fixtures must be checked regularly to ensure a fault-free operation.

The barndoors is designed and intended to be mounted on the fixture without the use of any tools.

Please note that this is an accessory and is not included in the box!

Caution: Ensure the barndoor is fully fixed and safety cable is attached before putting fixture into use.

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

Symptom

Possible cause

Suggested action

No response from fixture.

No power to fixture.

Check that power is turned on.

Check cables and connections.

Internal fault.

Contact Beamz support or Beamz authorized

service partner. Do not remove base or yoke

covers. Do not attempt to replace a fuse or

carry out any repairs or service that are not

described in this User Manual unless you have

both authorization from Beamz support or

Beamz authorized service partner.

Fixture resets correctly but does not respond

(or does not respond correctly) to the

controller.

The controller is not connected.

Connect controller.

Bad DMX-line.

Inspect connections and cables. Correct poor

connections. Repair or replace damaged

cables.

DMX-line has no end resistance.

Insert DMX terminator plug in DMX output

socket of last fixture on DMX-line.

Incorrect fixture addressing.

Check fixture address and DMX mode settings.

A fixture is defective and is disturbing data

transmission on the DMX-line.

Unplug DMX IN and OUT connectors and

connect them directly together to bypass one

fixture at a time until normal operation is

regained. Have defective fixture serviced by an

authorized technician.

Pin 2 and 3 are reversed in XLR connection.

Inspect connections and cables. Install a

phase-reversing cable between the fixtures or

swap pin 2 and 3 in the fixture, that behaves

erratically.

Error after fixture reset.

Effect requires mechanical adjustment.

Check fixture’s software version and error

messages for more information. Contact

Beamz support or Beamz authorized service

partner.

Light output cuts out intermittently.

Fixture too hot.

Allow fixture to cool. Reduce ambient

temperature. Ensure free airflow around

fixture. Clean fixture if necessary.

LEDs damaged

Disconnect fixture and contact Beamz support

or Beamz authorized service partner.

The power supply settings do not

match local AC voltage and

frequency.

Disconnect fixture. Check settings and

correct if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 150.691 Star-Color 270Z Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info