Bedienungsanleitung BeamZ 151.200 (Seite 5 von 24) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

766343

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

REMOTE CONTROLL

Button function:

1. 151.200/151.202 Red LED (on /off), 151.201 ¼ Cool white (on/off)

2. 151.200/151.202 Green LED (on/off) , 151.201 ¼ Cool white (on/off)

3. 151.200/151.202 Blue LED (on/off) , 151.201 ¼ Cool white (on/off)

4. 151.200/151.202 White LED (on/off) , 151.201 ¼ Cool white (on/off)

5. Sound control

6. Strobe (keys 9+10 for speed up/down)

7. Fade (keys 9+10 for speed up/down)

8. Auto mode (keys 9+10 for speed up/down)

9. Up (speed)

10. Down (speed)

11. Enter/Confirm

12. DMX512 control

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

REPLACING THE LEDS

Compared to incandescent lamps, LEDs have a very long life and usually no replacement is required. However, just in case

there is a defect, a few spare LED modules are supplied.

1. Separate the cable connection between the LED curtain and the controller.

2. Open the zip fastener at the side of the LED curtain; the connections of the LED modules will be accessible.

3. Before disconnecting the plugs from the defective module, note the polarity (small marks “+” and “-” on the PCB). If

necessary, remove the retaining adhesive at the connectors in order to disconnect the plugs.

4. Connect the spare module using the same polarity.

5. From the front of the cloth, pull the black plastic ring around the LED from the PCB of the defective module and remove

the module.

6. Insert the LED of the spare module from the rear through the hole in the cloth and, from the front, insert a black plastic

ring through the cloth so that the two pins will engage in the corresponding holes provided on the PCB.

7. After replacing the necessary modules, close the zip fastener again.

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding

can cause greater accumulation of dirt on the unit’s optics.

 Make sure the area below the installation place is free from unwanted persons during servicing.

 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation.

 The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is

detected.

 In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned

monthly.

 The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.

 Clean with soft cloth using normal glass cleaning fluid.

 Always dry the parts carefully.

 Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.



ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 151.200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info