Bedienungsanleitung BeamZ 151.265 PS12W LED (Seite 4 von 20) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766399

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

REMOTE CONTROLLER

BLACK OUT Mode

Press <BLACK OUT> off existing modes. Press <BLACK OUT> return the last modes.

AUTO Mode

Automatic mode will enable you to run the automatic programs on the product.

To turn on Automatic mode:

1. Press <AUTO> on the remote controller.

2. Press <+> or <–> to choose between the different auto programs.

SOUND Mode

Sound-Active mode will enable the product to respond to the music.

To turn on Sound-Active mode:

1. Press <SOUND> on the remote controller.

2. Press <+> or <–> to choose between the different sound programs.

STROBE Mode

To adjust the strobe speed of the automatic program and the sound active program.

1. Press <STROBE> on the remote controller.

2. Press <+> or <–> to either increase or decrease the speed of the program.

3. Press <STROBE> again to turn off the strobe.

SPEED Mode

To adjust the speed of the automatic program and the sound active program.

1. Press <SPEED> on the remote controller.

2. Press <+> or <–> to either increase or decrease the speed of the program.

SENSITIVITY Mode

To adjust sound sensitivity for in Sound-Active mode

1. Press <SENSITIVITY> on the remote controller.

2. Press <+> or <–> to either increase or decrease sound sensitivity.

MANUAL Mode

1. Press <MANUAL> on the remote controller.

2. Press <R>, <G>, <B> or <W> (red, green, blue, white) to choose your colour.

3. Press again <R>, <G>, <B> or <W> (red, green, blue, white) to close your colour.

4. Press <+> or <–> to either increase or decrease the percentage of each colour.

FADE Mode

To adjust the FADE speed of the automatic program, the sound active program and the manual mode.

1. Press <FADE> on the remote controller.

2. Press <FADE> again to turn off the fade mode.

NUMBER 1~9

To adjust the brightness value of the automatic program, the Sound active program and Manual Mode.

Press digit <1> to <9> to change different brightness on the device.

The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts

prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery

support on the rear side of the remote control. Otherwise operation of the remote control is not possible.

If the range of the remote control decreases, replace the battery. For this

purpose, on the rear side of the remote control press the small bar with the groove to the

right (1) and at the same time remove the battery support (2). For operation, one 3 V button

cell type CR 2025 is required. When inserting, pay attention that the positive pole of the

button cell shows upwards in the support.

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning

frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

 Make sure the area below the installation place is free from unwanted persons during servicing

 Housings, fixations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation

 The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is

detected

 In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly.

 The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.

 Clean with soft cloth using normal glass cleaning fluid.

 Always dry the parts carefully.

 Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.



ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 151.265 PS12W LED Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info