Bedienungsanleitung BeamZ 152.521 (Seite 6 von 44) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766946

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are

present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if

any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing

materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original

factory box and packing.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The

arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains

voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also

be directly connected to the mains and may be used. No dimmer or adjustable power supply.

Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate

electrical ground to avoid the risk of electrocution or fire.

DISPLAY

The control board offer several features: you can simple set the starting address, run the

pre-programmed program or make a reset. The main menu is accessed by pressing the

Return-button, browse through the submenu by pressing Up or Down.

Press the Enter-button in order to select the desired menu.

You can change the selection by pressing Up or Down. Confirm every selection by

pressing the Enter-button.

You can leave every mode by pressing the Return-button. The functions provided are described later in this manual.

Note: When you turn on the laser for the first time, it will take some seconds to auto load the built-in show

DMX-512 CONNECTION

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the

first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.

5-pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be

implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used.

The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conducto

3-Pin XLR Female (Out) 5-Pin XLR Male (In)

Ground/Shield Pin 1 Pin 1

Data Compliment (- signal) Pin 2 Pin 2

Data True (+ signal) Pin 3 Pin 3

Not Used Pin 4

–

Do Not Use

Not Used Pin 5 – Do Not Use

At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between signal (-) and signal (+) into a 3-pin

XLR connector and plug this into the DMX output of the last fixture in the chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 152.521 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info