Bedienungsanleitung BeamZ 154.062 - DMX-024PRO (Seite 7 von 11) (Deutsch, Englisch, Holländisch, Spanisch)

765605

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Connections at the rear panel

On the rear panel are located a number of connectors and a slider control, i.e.: a small connector for the included power

supply (1), a block of 3 DIN connectors for MIDI (2, 3 and 4), a 3-pin DIN connector for the DMX signals (5) featuring a push

switch for polarity inversion (6) an RCA connector for an external audio signal (7) and a 6.3 mm jack for a foot switch (8).

BASIC

FUNCTIONS

FOR

PROGRAMMING

1) Activation of the programming mode:

Keep the RECORD/SHIFT button pushed in and press in sequence the flash buttons 1, 5, 6 and 8. These buttons are

located just below the slider controls in the upper row PRESET A. Release the RECORD/SHIFT button. The red

programming LED should light up.

2) Exit the programming mode:

Hold the RECORD/SHIFT button down and press simultaneously the REC/EXIT button. The red programming LED goes

off.

3) Erasing all programs (be careful !):

Activate the programming mode as described above in step 1. Hold the RECORD/SHIFT button down and press in

sequence the flash buttons 1, 3, 2 and 3 in the section PRESET A. Release the RECORD/SHIFT button. All stored running

light scenes are now erased from the ROM. All LEDs flash to confirm. Press the RECORD/SHIFT and the REC/EXIT

buttons at the same time to leave the programming mode.

4) Erasing the RAM:

The RAM is used as an intermediate memory for a number of running light scenes during the programming process. If you

make a mistake during the programming, you can erase the RAM. Activate the programming mode as described in step 1.

Hold the RECORD/SHIFT button down while pressing the REC/CLEAR button. All LEDs flash once to indicate that the

RAM has been erased.

PROGRAMMING RUNNING LIGHT PATTERNS (SCENES)

1) Activate the programming mode as described in the Basic Functions.

2) Select the mode 1-24 single (the green LED lights up) via the MODE SELECT button. In this mode, you can use all 24

channels.

3) Push the MASTER slider controls A and B to their maximum positions. Note: Control A completely up and control B

completely down.

4) Set the required light position via the slider controls 1 to 24.

5) Press the RECORD/SHIFT button once to store this position in the RAM.

6) Repeat steps 4 and 5 with different positions of the slider controls in order to get an optimal light effect. You can store

up to 99 steps per memory.

7) The programmed steps must now be transferred from the RAM to the ROM. Proceed as follows: Select a memory

page (1 to 4) via the PAGE/REC CLEAR button. Hold the RECORD/SHIFT button down and press one of the flash

buttons 1 to 13 in section PRESET B. You can store up to 99 steps per memory. There are in total 4 pages with 12

memories each.

8) Exit the programming mode (press RECORD/SHIFT and REC EXIT buttons). The red programming LED must go off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 154.062 - DMX-024PRO Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info