Bedienungsanleitung BeamZ 154.090 - DMX-240 (Seite 8 von 16) (Deutsch, Englisch, Holländisch, Spanisch)

765607

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Channel Setting

This device can control up to 12 x 20-channel scanners. The first 8 channels of each scanner can be controlled

through the 8 faders. The next 8 channels are controlled through the 8 faders and the PAGE selection button (10) on

page B.

If the scanner features more than 16 channels, set the channels as follows:

• Press the PROGRAM button (11) until the LEDs blink.

• Press the FINE (25) and the MODE (28) buttons simultaneously until the ASSIGN LED (20) turns on.

• Select your scanner by pressing the corresponding SCANNER button (1).

• Adjust the SPEED fader (23) to select the scanner channel (e.g. channel 9 or 10).

• Adjust the FADE TIME fader (24) to select the respective control channel of the controller (e.g. PAN (27A) or TILT

(27B) wheel).

• To set channel 19 and 20, press the PAGE selection button (10). The PAGE B indicator LED (9) will light. Repeat the

two previous steps.

Example: Set the SPEED fader (23) to channel 9 and the TIME fader (24) to X. This means the 9th channel of the

scanner will be controlled by the PAN wheel (27A).

FADE TIME Assignment

With this function you can determine whether the fade time should be assigned to the pan/tilt movement or to all DMX

channels. This is useful when the mirror or the moving head movement should be carried out slowly but the gobos

and colours should be changed quickly.

• Turn of the device.

• Simultaneously press and hold the MODE (28) and the TAP DISPLAY button (17).

• Turn on the device. Press the TAP / DISPLAY button (17) in order to switch between the two modes (ALL CH for all

channels and ONLY X/Y for pan/tilt movement only).

• Simultaneously press and hold the MODE (28) and TAP / DISPLAY button (17) to memorise your settings. All LEDs

on the panel will flash indicating the setting has been saved.

Operation

Manual

To select the manual mode, press the AUTO / DEL button (21) until the MANUAL LED (14) lights.

In manual mode you can call up the connected scanners manually and control them through the faders. Note that the

settings cannot be memorized. Select the desired scanner using the corresponding SCANNER button (1). Adjust the

desired function through the faders.

• Checking a BANK / SCENE

Select the desired bank using the BANK buttons (16 and 17). Select the desired scene using the SCENE buttons (3).

• Checking a CHASER

Select the desired chaser using the CHASER buttons (22). Press TAP / DELAY (17). The display will show the steps

in the chaser. Press the BANK buttons (16 and 17) to see each scene.

• The PAGE selection button (10)

Use this button to adjust the channel faders (4) from CH1 ~ 8 (page A LED is lit) to CH9 ~ 16 (page B LED is lit) or

both of them (both LEDs are lit).

• The DISPLAY button (17)

Use this button to switch the display from a DMX value (0 ~ 255) to a percentage (0 ~ 100%).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 154.090 - DMX-240 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info