Bedienungsanleitung BeamZ 160.756 SNOW 500 (Seite 5 von 26) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766826

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

UNPACKING INSTRUCTION

ATTENTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and

have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from

shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be

returned to the factory, it is important that the product be returned in the original factory box and packing.

If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation

water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to

this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and

may be used. No dimmer or adjustable power supply.

WARNING! Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground

to avoid the risk of electrocution or fire.

INSTALLATION

Step 1: Place the unit on a flat surface and in a suitably large area with at least 50 cm of open space around the unit.

Step 2: Fill the fluid tank with Beamz snow fluid.

Step 3: Plug the power cord into the outlet and turn on the unit, put the power switch to the “ON” position. The LCD display will show “WARMING

UP”. After few seconds the LCD display will shows “READY”.

Step 4: Using the LCD display panel, set the unit to the desired operating mode.

Step 5: Turn off the unit, put the power switch to the “OFF” position and pull out the power cord from the outlet.

WARNING! Use only original Beamz snow fluid. Warranty will be voided if any other type of liquid is used, improper use of liquid may lead

to machine failure and malfunction.

OPERATION

When display shows “READY”, you can start producing haze and adjust the settings via LCD display panel.

DESCRIPTION

Man Vol Out xxx%

Adjust the manual volume output within the range of 0% to 100% by

means of the Up/Down keys.

Interval Set xxxS

Adjust the interval between 1 to 100S by means of the Up-/Down keys.

Duration Set xxxS

Adjust the duration between 1 to 100S by means of the Up-/Down keys..

Volume Out xxx%

Adjust the volume output within the range of 0- 100% by means of the Up-

/Down keys.

DMX 512 #xxx

Adjust the DMX address for DMX control by means of the Up-/Down keys.

Wind For Class xx

Adjust the wind output during the function within the range of 0- 100% by

means of the Up-/Down keys.

Wireless

Turn on/off wireless remote

WIRELESS REMOTE

A: ON / OFF

B: ON / OFF

C: Increase output level

D: Decrease output level

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 160.756 SNOW 500 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info