Bedienungsanleitung Bebetel MOBILE (Seite 53 von 57) (Deutsch, Englisch, Französisch)

515347

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Note:

 If the number is entered correctly there will be one beep at the end of the input. Wrong re-entering will

provoke two beeps. Incorrect number will not be stored so the former value remains active.

 If you key a wrong number set function switch to OFF and repeat steps 1 to 7.

9.3 Auto answer

If you want to change the number of rings prior to answer, you can proceed as follows:

1. Set function switch to PROG

2. Press .*.

3. Enter .9 .7 .1 .3 .4 .7 <n> (n ¦ see table below)

4. Press .#.

5. Enter .9 .7 .1 .3 .4 .7 <n> once again for confirmation

6. Press .#.

7. Set function switch to OFF

<n> Comment

2..9

bébétel

answers call after n rings

bébétel

does not answer any incoming call

Note:

 If the number is entered correctly there will be one beep at the end of the input. Wrong re-entering will

provoke two beeps. Incorrect numbers will not be stored so the former value remains active.

 If you key a wrong number set function switch to OFF and repeat steps 1 to 7.

 Default value is 2 rings.

10 Trouble shooting

You can clear most faults checking the following list. If a problem cannot be resolved please check our

interactive error handling on our homepage www.bebetel.com or contact Info- +41 (0)56 648 40 40.

Problem Cause and/or remedy

The indicator LED does not

shine when switched on

Replace battery  7.7

Three beeps when switched on

Battery is low ¦ replace it  7.7

Six beeps when switched on

No connection with test call ¦

dial tone not present

 bébétel

is not connected to an analogue telephone line

 Pin compatibility error (telephone cord <-> telephone line)

 Telephone network is down

 Line is busy because a parallel telephone set is in use

¦ plug in telephone cord

¦ check telephone cord

¦ make a call with another telephone set

¦ Mobile phone is not detected, not connected or not compatible with

bébételMOBILE

( 1.3 or www.bebetel.com/mobiles)

No connection with test call ¦

dial tone present

 Telephone number has been wrong

 Called subscriber does not accept call

No access using dialling-in

functionality ¦ call will be

disconnected after PIN-code

input together with two beeps

 Wrong PIN-code has been entered ¦ re-program PIN-code

 Used telephone set does not support touch tone or is in the wrong mode

No access using dialling-in

functionality in mobile use:

 Volume incorrect ¦ adjust connected mobile phone to medium volume

bébételMOBILE

: In mobile use only possible with mains supply and

if the attached mobile phone supports the speak with child -mode

( 1.3 or www.bebetel.com/mobiles).

Mode cannot be changed using

touch tone commands

 Used telephone set does not support touch tone or is in the wrong mode

¦ for instance pulse-dialling or an ISDN-telephone

 Mobile use: Volume incorrect ¦ adjust connected mobile phone to

medium volume

bébételMOBILE

: In mobile use only possible with mains supply and

if the attached mobile phone supports the speak with child -mode

( 1.3 or www.bebetel.com/mobiles).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bebetel MOBILE Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bebetel MOBILE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info