Bedienungsanleitung Beefeater Discovery 1100 series (Seite 22 von 22) (Englisch)

810606

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Adjust Aeration Screw in Burners

At the air entry side of each burner turn the aeration screw anticlockwise until no thread is protruding

into the burner, and lock to place with a locking nut. Do not completely remove the screw. Once adjusted,

re-seal position with red paint. This must only be done by a qualified person.

Replace All Parts Into Position In The Barbecue.

Refit the burners and locking clips that hold each burner in position. Replace all Vaporizers, cooking plates

and grills, and Hood. Check the operation of each burner.

Perform a Leak Test and Pressure Test

Use the following procedure to check for gas leaks. Never use a naked flame to check for gas leaks.

1. In a small container, mix up a solution of water and detergent or soap. Mix the solution well.

2. For LPG make sure that the gas supply valve on the gas cylinder is turned on. For NG make sure that

the gas line is correctly fitted to the appliance.

3. Make sure that the gas control valves on the appliance are all turned off.

4. Using a brush or spray bottle apply the solution to the gas line and each join in the gas line.

5. Bubbling of the solution will indicate that there is a leak present.

6. Re-tighten or re-seal any joints that are leaking.

7. If a leak persists then contact your distributor or the manufacturer for assistance.

Use the following procedure to test the pressure

8. Remove the far left burner.

9. Place a hose and pressure gauge over the control valve’s injector.

10.Turn all other burners on, including the side burner.

11.Turn the LH valve with measuring devise on as well, and take reading.

12.Pressure reading for Natural Gas should be as in table below for each region.

Replace the Data Label

Peel the replacement label from its backing sheet and place this over the existing data label to indicate

that the unit is configured for Natural Gas. This label can be found on the front of the barbecue body.

NOTE: To convert the BeefEater barbecue from Natural Gas to LPG, all of the above

steps must be reversed including the replacement of the Data Label.

NOTE: The correct spanner to be used with these Injectors is 9/32” or 3BA.

Connect to the natural gas supply

Connecting to Natural gas supply must be performed only by your natural gas provider or service company.

Warning:

If the appliance is using natural gas, a qualified installer should be called in to

install the appliance. The quick coupling should comply with ISO 6150, and the

quick coupling is not sold with appliance.Warning: If LPG is connected to NG set

appliance, fire and injury may occurred.If use non-correct NG quick coupling, gas

leakage, fire and injury may occurred.

After conversion to natural gas, the product must be secured with a chain and

cannot be moved. The barbecue need to be bolted to the ground.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beefeater Discovery 1100 series Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beefeater Discovery 1100 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info