Bedienungsanleitung Beefeater Signature 3000 series (Seite 5 von 20) (Englisch)

810611

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The Cylinder Compartment

If the gas for your barbecue is to be supplied by a portable LPG/propane cylinder, you will need to ensure that

adequate provision is made to house the cylinder safely. The following must be adhered to:

Keep out of heat: The cylinder and hose must be sheltered from the sun’s direct heat. The flexible PVC hose

assembly supplied must not be exposed to temperatures in excess of 60°C. DO NOT allow the hose to come

in contact with the hot surface of the barbecue body.

Keep cylinder upright: The cylinder must be housed securely. It must remain upright at all times. It can be

either attached to a firm vertical wall by a cylinder bracket, or stored on a firm level base.

Requirements for cylinder base:: If the cylinder is to be stored on a flat base, the base must be made from

non-combustible material. Soil or grass is not an appropriate surface. Ensure there is adequate drainage, and

that water cannot collect around the cylinder.

Requirements for cylinder compartment: Where the cylinder is to be kept inside an enclosure, you must

ensure there is 200 square centimetres of open ventilation at each of the top and the bottom of the enclosure,

for each cylinder stored in it. This prevents leaking gas from building up in a confined space. Gas vapour is

highly explosive and can cause serious bodily injury or damage to property if allowed to accumulate in a

confined space and ignited.

General Requirements

We recommend that this installation be done in a masonry structure and carried out by a professional

tradesperson. Other non-combustible material such as Hardiplank, Villaboard with metal studs may also be

used. This appliance must not be installed under or on any combustible material. Minimum clearance from

combustible construction materials to all sides of the appliance is 450mm.

The Barbecue Cavity

Your barbecue has been designed to sit into a cavity or cutout rather than be placed directly onto a flat

surface. It is important that the dimemsions of the cavity conform exactly to those listed below. This will

ensure the barbecue sits correctly in the cavity, and that the barbecue has sufficient ventilation to operate

efficiently and safely. It also allows room for any roasting hood to open freely,

In creating the cavity, you should ensure that you have convenient access to the gas connection point and

associated hardware:

If the gas for your barbecue is supplied by a portable gas bottle, you will need access to the gas connection

point, the gas hose and the gas cylinder at all times.

If the gas for your barbecue is supplied by a fixed piped gas supply, you will need access to the gas

connection point, the piping and the shutoff valve.

•

For Built-In Units Only

Built-in Cavity Dimensions

x 2 523mm

x 3 690mm

x 4 846mm

x 5 1003mm

525 mm

230 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beefeater Signature 3000 series Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info