In the top part of the surround, it is necessary to provide non closable convection air holes for a convection air output, inthe bottom part, there
is a need of convectional air input - minimal diameter depends on output of the fireplace insert, mentioned in the technical list. You need to
consider non effective parts of the grilles (20-40% of the grille area, depending on design also) when choosing the convenient grilles for
input/output of the convectional air and take into account also way of the using (in technical list, nominal output of the fireplace insert is
mentioned and the real output depends on the amount of wood in use, the real output can be for short period higher of 50%).
The minimal dimensions of the convectional air grilles for input and output are mentioned in the following chart:
Fireplace insert output (kW)
Convectional air input –grille dimension
(cm2)
Convectional air output –grille dimension
(cm2)
6-9
700
1000
10-15
850
1200
15-20
1100
1600
After the fireplace installation neither the air input nor the air vent can be restricted by building panels. We recommend
ordering a professional firm.
To prevent heat accumulation the holes for conventional air must be open during heating. No lockable grates, ribs, blinds, etc. can be installed into the
holes. In the top part the convection coating must be finishedby the partition wall above the hole, so as not to make a thermal pocket. (see Surround
diagram).
Convection cross-section between the insert and the coating as well as the insulation on the rear side –please check the chart with
measures of protection (see pict.06 )
Note: These minimal distances in accordance with the Equipment Certificate must be kept
to on all heights and widths of the fireplace insert so as to allow convection air to flow
through.
Convection air area:If a prefabricated area for convection air is not used (lining made of a galvanized sheet), it is necessary to maintain a
distance according to the chart on page n.6between the fireplace insert and rear thermal insulation layer.
The fireplace insert assembly: The fireplace insert can be placed on a fitted base after the making of the thermal insulation as in the
installation instructions. The fireplace insert is connected with the chimney by the connecting piece (smoke flue).
Extension joint:It is necessary to have an extension joint at least 3 mm thick between the insert and the coating. The extension joint can
be stemmed by a ropeor sealing tape.
Coating (fireplace surround):The coating of the fireplace insert which leads into the room must be made of non combustible material of
grade A1 (e.g. tiles, plaster coat, iron or ceramic tiles). There must not be any direct contact between the coatings and the fireplace insert.
The coating may overlap only on the separate carrying frame which is clamped to the wall. For adjustment, maintenance of a safety valve,
a pump and accessories or possible repairs it is necessary to provide the surround with service holes. These holes are necessary for these
operations and it is not needful to build the surround.
Ornamental beams: Ornamental beams are allowed in front of the fireplace coating at a distance of 1 cm at least if the ornamental beam is
not a part of the building and the intermediate space is such that it does not accumulate heat and the ornamental beam is notsituated
within the area of the insert heat radiation.
Fire protection in a heat radiation area
A minimum distance of 80 cm forwards and sideways must be retained in front of the firebox hole (pict.6, position 1). If the
protection against heat radiation is from both sides, a distance of 40 cm is enough (pic. 6, position 2).
frame
Part of
veneer
pict. 6
CONNECTION WITH THE CENTRAL HEATING SYSTEM
THE INSTALLATION OF THE FIREPLACE INSERT THE CENTRAL HEATING SYSTEM CAN BE REALIZED ONLY BY AN
EXPERT IN ACCORDANCE WITH NATIONAL STANDARDS AND THIS INSTALLATION MANUAL
Fireplace connection pict. 3
System of the central heating and the hot water fireplace insert
installation:
1.HOT WATER FIREPLACE INSERT
2.COLD WATER INLET DN 25 (BACKWARD)
3.WARM WATER OUTLET DN 25 (RISER)
4.CIRCULATING PUMP OF THE FIREPLACE
5.CLAP VALVE OF THE FIREPLACE
6.PRESSURE FELIEF VALVE 2,5 bar.
7.DISCHARGE PIPE OUTLET
8.OPEN EXPANSION BOX
9.SYSTEM OF RADIATORS
10.WARM WATER MAIN PIPE (RISER)
11.COLD WATER RETURN PIPE (BACKWARD)
12.THERMOSTATIC SAFETY VALVE
13.WATER SUPPLY CONNECTION
14.COOLANT LOOP
15.THERMOSTATIC MIXING VALVE
16.SENSOR OF A THERMOSTATIC VALVE
17.BLEED VALVE
Fireplace connection pict.4:
Central heating system with the hot water fireplace insert
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für BeF Home Hot water fireplace inserts wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
