Bedienungsanleitung Behringer EXPANSION CARD X-MADI (Seite 6 von 15) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

660554

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Warning

Failure to observe the following warnings may

lead to fatality or serious injury from re or

electric shock.

Before installing the card, you must refer to the owner’s

manual of the host device or to behringer.com to verify that

your host device supports this card, and to verify the number

of cards that can be installed in combination with other

BEHRINGER or third-party cards.

• Do not attempt to disassemble or modify the card.

Donot apply excessive force to board connectors or

other board components. Mishandling of board may

lead to shock, re hazard, or equipment failure.

• Disconnect the power cable from the main unit before

installing this card to eliminate shock hazard.

Caution

Failure to observe the following precautions may

lead to personal injury, or may result in damage

to equipment or other property.

• Do not touch the board’s metallic leads (pins)

whenhandling the card. Pins are sharp and may

causeinjury.

• The card is electrostatic-sensitive.

Before handling the card, you should briey

touch the main unit’s metal casing with

your bare hand so as to drain o any static

charge from your body. BEHRINGER assumes no

responsibility for data loss, equipment damage,

or injury caused by inappropriate handling or usage.

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT! This product, wheninstalled as indicated

in the instructions containedin this manual, meets FCC

requirements. Modications not expressly approved by

BEHRINGER may void your authority, granted by the FCC,

to use theproduct.

2. IMPORTANT: When connecting this product to

accessories and/or another product, use only high quality

shielded cables. Cables supplied with this product MUST be

used. Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in

the users manual, may cause interference harmful to the

operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the

source of interference, which can be determined by turning

the unit “OFF” and “ON”, please try to eliminate the problem

by using one of the following measures: Relocate either this

product or the device that is being aected by the interference.

Utilize power outlets that are on dierent branch circuits

(circuit breaker or fuse) or install AC line lters. In the case of

radio or TV interference, relocate/reorient the antenna. If the

antenna uses 300Ohm ribbon cable, use coaxial cable instead.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact BEHRINGER customer service.

FCC INFORMATION U.S.A.

1. Introduction

The X-MADI card is a multichannel audio interface expansion

card for the X32 series of digital mixers. It provides 32 channels

of MADI/AES10 input and output via bre-optic or coaxial cables.

This provides very long cable runs up to 2 km with ber-optic

connection and allows redundancy when combined with BNC

coaxial connectors.

2. Installation

Before you install the X-MADI card in the expansion slot of the

X32 console, you must check behringer.com to verify whether the

console rmware supports that card.

Caution – before installing the X-MADI card into the console,

you must make sure that the console’s power switch is turned o.

Malfunctions or electrical shock may occur otherwise.

1. Make sure that the mixer’s power is turned o.

2. Loosen the screws left and right that fasten the slot,

thenremove the slot cover or currently-installed card and

keep it in a safe place.

3. Before removing the X-MADI card from its protective bag,

we recommend touching the grounded metal chassis of the

console to prevent electrostatic discharges aecting the

sensitive electronic components. It is generally a good idea

to hold the card either by the face plate or by the two small

handles, but never touching the components on the circuit

board directly.

4. Align both edges of the card with the guide rails inside the

slot and carefully insert the card into the slot. Push the card

all the way into the slot to ensure that the contacts of the

card are correctly inserted into the connector inside.

5. Fasten the card using the included screws. Be aware that

damage or malfunctions may occur if the card is

not fastened.

Requirements

X32 Series console with rmware version 2.0 or higher.

10 11Quick Start GuideEXPANSION CARD X-MADI

Behringer EXPANSION CARD X-MADI Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info