660597

Behringer VMX1000USB Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
ENGLISH
PRO MIXER VMX1000USB User Manual
4
ENGLISH
PRO MIXER VMX1000USB User Manual
5
Control Elements2.
Fig. 2.1 Front view of the PRO MIXER VMX1000USB
Never connect equipment with line level signals to ◊
the highly sensitive phono inputs! The output signal
level of turntables is on the order of magnitude of
milivolts, while CD players and tape decks have signal
levels measuring in volts. Simply put, line signals are
up to 100 times stronger than those intended for
phono inputs. If you’re using phono inputs that can
be switched into line level (see
{ 36 }), always make sure
that the PHONO/LINE switch is in its correct position
(switch pressed!).
The
[10] GAIN control is used to set the level of the input
signal. The display
{ 13 } reads off the current signal level.
Every input channel features a 3-band equalizer (
[11] HIGH,
MID and LOW) with kill characteristic. This way, a signal
can be lowered (-32 dB) much more than it can be
increased (+12 dB). For example, this function is useful
when you need to suppress a particular frequency range
in a music track.
The overall signal level is also dependent on the
◊
EQ settings. You should first adjust the EQ before
adjusting the signal level.
By using the
[12] EQ BYPASS key, you can deactivate the
3-band equalizer. This way, you can easily compare
the processed and the unprocessed signals with one
another; or, you can alternate between extreme EQ
settings and the “raw” signal, creating cool effects.
You can read off the level of input signals (post EQ) using
[13]
the 4-digit LEVEL meter.
Determine the channel volume using the
[14]
60-MM cHANNEL fader.
Pressing the
[15] PFL key routes the respective input so that
it can be monitored on the headphones (corresponding
LED is lit). You can also dial up several channels and
listen to them simultaneously (see also chapter 2.4
“HEADPHONE section”).
MAIN OUT section2.3
The [16] VOL 1 control is used to adjust the output volume on
the MAIN 1 output (see
{ 41 }).
The
[17] VOL 2 control is used to adjust the output volume on
the MAIN 2 output (see
{ 46 }).
To adjust balance on the MAIN 1 output, use the
[18]
BAL 1 control.
You can read off the MAIN 1 audio signal volume level on
[19]
the LEVEL MEtEr.
The
[20] POWEr switch powers the PRO MIXER on. You should
always make sure that the POWER switch is in the “Off”
position when initially connecting the unit to the mains.
Please take note: Merely switching the unit off does
◊
not mean that it is fully disconnected from the mains.
When not using the unit for prolonged periods of time,
please unplug the unit’s power cord from the
power outlet.
Always turn the power amps on last to avoid inrush
◊
currents that can easily damage your speakers. And,
to avoid sudden and unpleasant surprises for your
ears, make sure there is no signal at the PRO MIXER
before turning on the power amps. To be sure, slide all
the faders to the bottom and switch all controls to the
zero position.
HEADPHONE section2.4
The PFL signal is your headphone signal used to monitor
music without influencing the MAIN signal (PFL = Pre
Fader Listening).
This is the unbalanced
[21] PHONES connector for your
headphones. Your headphones should have a minimum
impedance of 32 Ohms. For example, the BEHRINGER
HPX2000 headphones are ideally suited for this purpose.
If the
[22] MODE switch is in the “SPLIT” position, the PFL
signal is on the left, and the MAIN signal is on the right.
The MIX control (see
{ 23 }) has no function in this case.
While in “STEREO” mode, you can alternate between
MAIN and PFL signals using the MIX control.
When in “S
[23] TEREO” mode, use the MIX control to
determine which signal is heard on the headphones.
When MIX is in its left-most position (PFL), you can only
hear the headphone signal selected previously using
the PFL keys of the input channels (see
{ 15 }). When MIX is
in its right-most position (MAIN), you can only hear the
MAIN audio signal. Placing the MIX control somewhere
in between those two extreme positions determines the
volume ratio of the two signals. If the MODE switch is
in its “SPLIT” position (see
{ 22 }), the (PFL) MIX control has
no function.
The
[24] VOL control determines the volume of the
headphone signal.
2.5 XPQ 3D surround function
The XPQ 3D surround function is a built-in effect that
gives your music a nice finishing touch, making every
performance truly memorable. By widening the stereo
base, the sound comes through more alive and transparent.
Using the XPQ ON switch
{ 25 } activates the XPQ 3D surround
function (corresponding LED is lit) and the XPQ control
{ 26 }
determines the intensity of the effect.
Effects loop2.6
Using the [27] rEt control, you determine the volume of the
effects signal that can be brought in at the RETURN input
on the rear (see
{ 49 }). To get the effects signal, you need to
connect the inputs of an effects unit to the SEND outputs
(see
{ 48 }) of your VMX1000USB. The outputs of the effects
unit are then connected to the RETURN inputs of your
mixer.
Microphone channels2.1
These are the balanced XLR connectors for dynamic [1]
microphones.
Using the 3-band microphone equalizer (
[2] HIGH, MID
and LOW), you can change the sound of your voice and
optimally adjust it (+/-15 dB).
The
[3] AUX control adjusts the volume of the MIC AUX send
signal laid out at the rear panel MIC AUX SEND connector
(see
{ 38 }).
Use the
[4] VOL control to adjust the microphone signal
volume.
Your PRO MIXER features a talk over function. It works very
simply: as soon as you talk into your mike while a track is
playing, the track’s volume is lowered. When talking to the
audience, this function is useful because it makes your voice
come through over the music.
Use the
[5] tALK key to activate the talk over function
(its LED is lit).
The
[6] SENS control changes the sensitivity of the talk over
function. The lower it is set, the louder does the mike
signal need to be in order to suppress the music signal.
Use the
[7] DPt control to determine the extent to which the
music signal is lowered.
Use the
[8] MIc ON switch to activate the microphone
channel. If its LED is lit, the channel is active.
Stereo channels2.2
Select the input signal for the stereo channels using [9]
the INPUt key. “Phono” is intended for connecting a
turntable. “Line” and “CD” have to be selected for all
other signal sources (e. g. CD or MD players). Unlike
the first three channels, channels 4 and 5 each feature
two line inputs. On the rear panel, a special feature lets
you change the input sensitivity of the phono inputs of
channels 1 through 3 to line level, so that you get more
flexibility (see
{ 36 }). Audio sent from a computer to the
VMX via USB cable is routed to channel 1. This signal is
mixed with the LINE input.
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

behringer-vmx1000usb

Suche zurücksetzen

  • Was kann ich mit dem usb Anschluss anfangen? Brauche ich dafür eine spezielle Software? Eingereicht am 18-4-2023 11:52

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer VMX1000USB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer VMX1000USB

Behringer VMX1000USB Kurzanleitung - Deutsch, Englisch, Französisch, Portugiesisch, Spanisch - 15 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info