Bedienungsanleitung Behringer VT250FX (Seite 5 von 13) (Englisch)

660561

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

5 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual

(13) With the MIDDLE control (VT100FXH and VT100FX only) you can raise or

lower the midrange frequencies on the OVERDRIVE channel.

(14) The TREBLE control adjusts the treble frequencies on the OVERDRIVE channel.

(15) Use the CONTOUR control for additional, highly characteristic adjustment

of the midrange, allowing you to easily create traditional as well

as ultra-modern guitar sounds.

(16) The VOLUME control adjusts the volume level of the OVERDRIVE channel.

2.1.3 DIGITAL FX

(17) The DIGITAL FX LED lights up when the eects processor is active.

(18) Use the FX PRESET control to select one of 16 eects.

Preset FX

1 - 4 Chorus/Delay

5 - 8 Delay

9 - 12 Chorus

13 - 16 Flanger

Tab. 2.1: Eects

(19) The FX LEVEL control adjusts the mix ratio between the original and

the eect signal.

(20) The REVERB LEVEL control determines the eect intensity of the

additional reverb eect.

(21) The FX LOOP MIX control (VT100FXH and VT100FX only) determines

the eect intensity of the external eect (see Chapter 2.2.1 FX LOOP).

2.1.4 MASTER section

(22) The MASTER VOLUME control adjusts both the overall volume and

the line out/headphones volume.

(23) The VTC push button activates and deactivates the VTC Virtual Tube Circuitry.

(24) The CD IN connector allows you to connect the output signal of a CD player,

tape deck, or CD/MD walkman. For example, you can play back music CDs or

CDs accompanying a guitar tutor while practising. This connector can also

be used as a LINE OUT output. In this case, the guitar signal is output with no

speaker simulation applied and can be routed to an external amp or mixing

console. This will not mute the VIRTUBE’s built-in loudspeaker.

(25) The LINE OUT/PHONES jack is for headphones connection. Internal speaker

simulation is applied to the headphones signal in order to produce an

authentic signal. The VIRTUBE’s built-in loudspeaker is muted when this

connector is used.

◊ The headphones output signal can also be routed to a mixing console or

other sound reinforcement system. To do so, connect the headphones

output with the line input on the mixing console. Use a standard cable

with 1/4" TS connectors. If hum problems occur, you could insert a

DI box, e.g. BEHRINGER ULTRA-DI DI100 or DI120.

◊ Some headphones tend to produce distortion with too high

volume level. Please turn down the volume a bit, until distortion stops.

(26) The POWER switch turns your VIRTUBE on and o. It should always be in the

OFF position when connecting the unit to the mains.

◊ Please note: Merely switching the unit off does not mean that it is fully

disconnected from the mains. To disconnect the unit from the mains,

pull out the mains connector. Before installation, please make sure

that the mains connector has not been damaged. If you do not use the

unit for an extended period of time, please disconnect it at the mains.

2.2 Rear panel

(27) The VIRTUBE is connected to the mains using a standard IEC receptacle.

A suitable power cord is included with the unit.

(28) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to

the mains, ensure that the voltage setting matches your local voltage.

Blown fuses must be replaced with a fuse of the same type and rating.

On some units, the fuse holder can be switched to one of two positions,

i.e. 230 V and 120 V. Please note: when operating the unit outside Europe at

120 V, a higher fuse rating is required (see Chapter 4, “Installation”).

(29) This is where the fan of the unit is located.

(30) The SPEAKER OUT connectors (only one on the VT100FX and VT50FX)

can be used to connect external speakers with a miminum impedance of

4 Ω. The outputs of the VT250FX deliver 50 Watts of power per channel

(L/R). Always use speakers with a minimum impedance of 8 Ω to ensure

maximum power output. Using the SPEAKER OUT connectors will mute the

built-in loudspeakers.

2.2.1 FX LOOP

(31) The FX LEVEL button allows you to adapt the FX LOOP to the operating level

of an external eects device (+4 dBu/-10 dBV).

(32) The VIRTUBE provides a serial insert path for inserting external eects

(e.g. reverb processor). To do so, connect the FX SEND jack to the input of the

eects device.

◊ The FX SEND can also be used as a parallel output with no effects,

for example, to record a “dry” guitar signal. As long as the RETURN jack

is not in use, there will be no break in the internal signal path.

(28)

(27) (29)

(30) (35)

(33) (31) (32) (34)

Fig. 2.2: VIRTUBE control elements (rear panel)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer VT250FX Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer VT250FX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info