Bedienungsanleitung Behringer X32 Producer (Seite 24 von 74) (Englisch)

660493

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

24 X32 PRODUCER DIGITAL MIXER User Manual

5. Topic Guide

5.1 Starting up, shutting down,

and rmware updates

We recommend switching the X32 PRODUCER on before any active sound

reinforcement system is connected. The function called “Safe Main Levels”,

located in the Setup/General Preferences screen, automatically turns down the

main LRC bus levels when booting the console, and also prevents any scene

loading actions from aecting (specically turning up) the main levels.

Synchronization and Sample Rate settings can also be adjusted on the Setup/Cong

page, but please note that changing the sample rate will require a console reboot.

◊ Please Note: Settings under ‘Link Preferences’, ‘Panning Mode’,

and ‘DCA groups’ are stored with the Scene data while all other settings

made on the Setup/Config page are not stored in any preset and will

not be initialized either. Please verify before using the X32 PRODUCER

that the sample rate is set correctly and if the synchronization source is

selected appropriately. If set to external synchronization via one of the

two AES50 ports, while no clock source is actually connected or switched

on, then the corresponding small square icon in the main display’s top

row would be red rather than green. In normal state you should only see

1-4 green squares in the top section depending on the units connected.

Note that if the X32 PRODUCER has previously been in use by somebody else,

and you feel unsure about its actual status, you can reset it to default settings in

either of two convenient ways:

1. While the console is booting up and the “X32” logo appears on the screen,

press and hold the “Scenes / UNDO” button, keeping it depressed until the

console is fully operational and the Home screen is displayed. The console

will now be in the exact same state as it was when rst shipped from the

factory. However, you can immediately revert back to the status the console

was in before being switched o by pressing the Scenes/UNDO button.

2. You can also reset the console any time after booting by pressing

“Setup/Cong” -> “Initialize”.

The X32 PRODUCER regularly stores the console’s status to its onboard ash

memory, sothere is usually nothing wrong with switching it o, and you do

not have to explicitly save the current status. However, when a large number

of parameters have been recently changed, storing all of them to ash can take

up to 1 minute, in a “worst-case” scenario. In order to prevent any errors by

losing power during this type of storage operation, we recommend using the

“Safe Shutdown” function from the Setup/Global page, an operation similar to

un-mounting a USBthumb-drive from your PC.

Updates:

The X32 PRODUCER rmware can easily be updated by performing the

following steps:

• Download the new console rmware from the X32 PRODUCER product page

onto the root level of a USB thumb drive

• Plug the USB thumb drive into the front panel USB connector while the

console is turned o

• Hold the USB View button depressed while switching the console on.

While booting, the X32 will run a fully automatic rmware update,

which will take 2-3 minutes longer than the regular boot sequence

When no update le is available on the USB drive, or when it is corrupted,

the update mode will remain active, preventing the X32 PRODUCER from booting

regularly. Switch the console o and back on without holding the USB View

button to boot the console with the existing rmware.

The USB socket is not suitable for other non-memory USB devices like keyboards,

mice, lamps, etc.

5.2 Default setup for connecting to monitoring

and P.A. systems

The X32 PRODUCER comes pre-congured with the local XLR inputs connected to

input channels 1-16, and XLR outputs 1-6 connected to the mix bus masters 1-6.

The Main LR (stereo) signal is normally put out on XLR outputs 7 and 8.

The Monitoring outputs on ¼" connectors, and the Phones output always carries

either the Monitor Source signal or any solo signal, whenever a solo button is

active. Press the View button in the Monitor section to check or change the solo

and monitoring preferences.

1. Power up the X32 PRODUCER console rst, before any connected power amps

or speakers are switched on.

2. Connect cables to XLR outputs 7 and 8 on the rear panel, connecting the

other ends of the cables to the inputs of your P.A. system. These normally

carry the main stereo bus left and right.

3. All buses or input channels that are to be put out on the main PA system

must have their Main LR Bus switches on. Use the selected channel’s pan

control to place the signal within the main stereo eld, and the channel’s

fader to set the volume.

4. Use the rear panel Monitoring outputs to connect monitor speakers or, ifyou

prefer, use the ¼" output in the front edge to connect your headphones.

Youwill either hear the monitor source signal, which is Main Stereo by

default, or any channel with its solo button being active.

5.3 How do I connect a microphone, process its

signal and send it out to the P.A. system?

1. Press the Select button of a desired input channel (for example, channel 1 on

the “Channels 1-8” input layer) and make sure the channel fader is down.

2. In the channel processing section in the upper left hand corner, make sure

the phantom power is switched o.

3. Connect a microphone to XLR input 1 on the X32 PRODUCER’s rear panel.

4. Press the 48V button to switch phantom power on for channel 1

(if the microphone requires it, such as a condenser microphone).

Note - It is best practice to mute the respective channels prior to switching

their phantom power supply on or o. Otherwise, the change of charge

may cause an audible popping noise. Gain adjustments might also produce

audible click noise when adjust shortly after having switched phantom

power on or o.

5. Use the Gain control to adjust the gain level as necessary, using the input

meter as a guide.

6. Switch on and adjust the Low Cut lter as needed to remove rumble or

windnoise.

7. Adjust the channel equalizer controls to sculpt the sound quality of the

microphone signal.

8. Adjust the channel Gate and Compressor controls as desired. Note that by

pressing the “view” button in the compressor or gate section, the main

screen will switch to the compressor or gate display for the selected channel,

oering additional compressor or gate controls beyond the dedicated

top-panel controls.

9. Turn on the “Main LR Bus” switch in order to route the selected signal to

the main LR, then adjust the Pan control to place the signal within the

stereoeld.

10. Adjust the Channel 1 fader to the 0 dB region, then slowly turn up the main

LR fader until you hear the mic signal amplied through your P.A. system.

Behringer X32 Producer Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Producer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info