Bedienungsanleitung Behringer X32 Producer (Seite 65 von 74) (Englisch)

660493

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

65 X32 PRODUCER DIGITAL MIXER User Manual

5. Rotate the 4th encoder to select the specic signal source to feed the

currently selected channel of the stereo recorder. Choices include:

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Bus Outputs

• Any of the 6 matrix outputs

• Any of the 32 direct outputs

• Direct Outputs Aux 1-8

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback

6. Rotate the 5th encoder to select the signal tap point that the selected audio

path is tapped from when feeding currently selected channel of the stereo

recorder. Choices include:

• Pre EQ

• Post EQ

• Pre-Fader

• Post-Fader

7. Tap the 6th encoder to toggle the “playback folder” mode on/o.

• When playback folder mode is OFF, the transport will stop after playing

the currently selected audio le. This is useful for situations like

triggering audio cues or sound eects in a theatrical setting.

• When playback folder mode is ON, the transport will continue playing

back all audio les residing in the currently selected folder one by one.

This is useful for playing back several songs during a break in the main

set, allowing the attached USB drive to act as a source for “break music”.

7.13 Assign Screen

The assing screen allows setup for the eight user-assignable buttons. Using this

screen, the console operator can assign 3 sets of 8 custom controls to be available

for adjustment at all times.

The assign screen contains the following separate tabs:

Home: This screen provides a general overview of the 8 assigned controls for all

three control sets at the same time.

Set A: This screen allows assignment of dierent console parameters to the

8custom controls for set A.

Set B: Works as described above but for custom controls set B.

Set C: Works as described above but for custom controls set C.

7.13.1 Assign Screen: Home Tab

The assign screen’s “home” tab provides a visual overview of the 8 assigned

controls for all three sets at the same time.

The home tab oers visual feedback of the controls that have been assigned to

all three sets of custom controls, without having to bank between the three sets

one-by-one or relying on the abbreviated syntax shown in the custom control’s

dedicated LCD displays.

To adjust the various settings on the home tab, perform the following steps:

1. Rotate any of encoders 1-5 to move screen focus to the dierent custom

assignable encoders and buttons in the A, B, and C sets. The controls

currently selected with each of the four encoders are highlighted with a

green outline.

2. Tap any of encoders 1-5 to switch to the edit screen for the specic custom

control that was highlighted on the home tab screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Producer Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Producer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info