Bedienungsanleitung Behringer X32 Rack (Seite 24 von 64) (Englisch)

660494

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

24 X32 RACK DIGITAL MIXER User Manual

5.12 Remote control

The X32 RACK hosts an Ethernet port on its rear panel which can be used to

connect and remote control it over a network via the X32-Mix on an iPad or the

X32-Edit application on a PC. To be able to do this the X32 RACK has to be set

up properly.

• Press the SETUP button next to the screen.

• Go to the Network tab.

• Use encoder 1 to choose between IP address, Subnet mask and Gateway.

Adjust the address elds with the encoders 2-5 and assign the selected

numbers with encoder #6.

• Set an IP address which ts your network, normally 192.168.0.X.

The IP address should be free within the network.

• Set your subnet mask according to your network,

normally255.255.255.0

• Set your gateway, if required.

Now get your iPad or remote PC into the same network and open the X32-Edit.

PC:

• On the X32-Edit, choose setup on the right side and the network tab.

Enter the IP address of the X32 in the network and press connect.

• If the software has connected to the X32 you can also synchronize them

in 2 directions. Console -> PC means all settings in the X32 will be

loaded into the X32-Edit. PC -> Console means that all settings in the

X32-Edit will be written to the console.

X32-Mix

• For the X32-Mix remote, open the program on your iPad (make sure the

iPad is connected to the same network as the console).

• On the startup screen, a popup should appear. Enter the IP of the

console, press “Go Online”, et voilà: you are connected and can control

the X32 RACK with your iPad.

5.13 Recording a 2-track directly with

theconsole

The X32 RACK oers the possibility to record a 2-track of your mix (or any other

selection of signals) directly onto a USB-stick/external USB hard disk:

• Plug a FAT-formatted (FAT12, FAT16, FAT32) USB stick into the USB port

on the front panel.

• Press the USB button above the USB port and the home screen of the

recorder will show up with a nice emulation of an old tape deck.

• On the cong tab you can select the source for the recording, default is

main L and R.

• Press RECORD (encoder #5) to record your mix.

• To adjust the volume during playback, use the Channel Select knob to

select A7 to adjust the left and right channels. The stereo channels are

linked by default, so adjusting A7 (left) will automatically aect the

right channel as well.

Remarks:

Due to the FAT format of the stick, the le size will be limited to 2 GB, which is

about 3 hours of stereo recording. Please test the recording capability of your USB

device before you do the “real stu” as some sticks may not be supported or be

too slow. We also recommend you defragment your USB device prior to recording.

The recording will be done as 16-bit WAV le with the selected sample frequency

of the console.

Please also note that it is possible that the specications of USB storage devices

may be changed by the manufacturer without any change in physical appearance

or notication.

5.14 Saving and recalling scenes

Follow the steps below to save and recall scenes in the console, allowing dierent

congurations to be recalled at a later time.

• Adjust all settings of the console so that all elements of the mix are

asdesired.

• Press the Scenes button. The Main Display will show various controls for

saving and recalling console scenes.

• Press the rotary control labeled “save” to save the console’s current

conguration to the next available empty scene and label it with a

customname.

• Adjust the console to the next desired conguration, and repeat the process

above as needed, saving additional scenes to additional empty slots.

• To recall a scene, rotate the rst encoder to scroll through the list of saved

scenes. A gray box will indicate which item is currently selected.

• When the desired scene is selected with the gray box, press the rst encoder

and the console will switch to that scene. All console parameters will switch

to the state they were in when saved to the scene that was just recalled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Rack Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Rack

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info