Bedienungsanleitung Behringer X32 Rack (Seite 51 von 64) (Englisch)

660494

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

51 X32 RACK DIGITAL MIXER User Manual

7.8 Monitor/Talkback Screens:

The monitor/talkback screen contains the following separate tabs:

Monitor: This screen controls various solo options, dimming, speaker delay,

andsources for the control room output.

Talkback A: This screen controls various adjustments for the talkback A path

ofconsole.

Talkback B: This screen controls various adjustments for the talkback B path

ofconsole.

Oscillator: This screen oers various controls for the onboard oscillator and how

it is routed throughout the console.

7.8.1 Monitor/Talkback Screen: Monitor Tab:

The monitor tab controls various console options related to the solo bus, aswell

as the console’s control room outputs. These options include various solo

settings, speaker dimming, speaker delay, and selection of sources for the control

room output.

To adjust the various settings on the monitor tab, perform the following steps:

1. Adjust the 1st encoder to change the gain of the monitor signal. This digital

gain stage occurs as a rst preliminary level control, before the top panel’s

analog-based monitor level control. A display above the encoder shows the

currently set gain value in dB.

• A multi-segment level meter is displayed on the color screen to allow for

proper gain staging of the monitor signal.

2. Adjust the 2nd encoder to scroll through the various solo methods

availableto the console when audio is routed to the solo bus.

Availableoptions include:

• Exclusive (Last): In this mode, pressing another solo button disengages

the previous solo.

• Solo Follows Select: When this method is selected, the audio of the

currently selected channel will automatically be sent to the solo bus.

Since a user will often select a channel to adjust its dedicated DSP

controls, this method is useful because the audio of the channel will

now already be feeding the solo bus where it can be monitored with

headphones in a live sound environment.

• Select Follows Solo: When this method is selected, any channel that is

soloed will automatically become the currently selected channel.

• Channel Solo AFL: With this method, the channel and select button do

not have any correlation to each other. When a channel’s solo button

is pressed, its audio is sent to the solo bus in “after-fader listen” mode,

reecting the current level of the channel fader and any channel DSP

that has been applied.

• Mix Bus AFL/PFL: This toggles the AFL/PFL setting for the mix

buses when they are soloed (as opposed to the soloing of a single

inputchannel).

• DCA Group AFL: This puts the contents of a soloed DCA group into after-

fader listen mode when the solo button is pressed on a DCA channel.

• Use Master Fader: This allows the Main Fader/mute button to control the

solo/mon output.

3. Tap the 2nd encoder to select and assign the currently chosen solo option.

4. Adjust the 3rd encoder to adjust the amount of digital delay that is applied to

the control room signal path. The display on the screen will show the current

amount of delay in feet, meters, and milliseconds.

5. Tap the 3rd encoder to toggle the delay function on/o.

TIP: The delay function is useful for aligning the sound of audio monitored

through headphones or speakers used at the Front-of-House position with audio

that is coming from the stage location.

By delaying the control room audio, it can be brought into alignment with

the slightly delayed audio that has to travel from the stage to the Front of

Houseposition.

6. Adjust the 4th encoder to set the amount of volume reduction that occurs

when the control room bus has its “dim” function enabled. The amount of

volume reduction ranges from -40 dB to 0 dB (no change).

7. Tap the 4th encoder to toggle the dim function on/o.

8. Adjust the 5th encoder to adjust the volume trim for the source currently

feeding the control room bus, allowing it to be level/matched with other

sources. The amount of trim can be adjusted from -20 dB to +20 dB.

9. Tap the 5th encoder to toggle the control room between mono and stereo

operation. This is very useful in a studio context for checking how a mix

sounds when played back on a mono speaker such as a clock radio.

10. Adjust the 6th encoder to select what specic signal source to monitor in the

control room bus. Choices include:

• O (No source)

• LR Bus

• LR + C/M

• LR PFL (pre-fader listen solo bus)

• LR AFL (after-fader listen solo bus)

• Auxiliary returns 5/6

• Auxiliary returns 7/8

11. Tap the 6th encoder to activate the signal source that has been chosen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Rack Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Rack

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info