Bedienungsanleitung Behringer Xenyx 1002B (Seite 8 von 12) (Englisch)

660465

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

8 XENYX 1002B User Manual

4.2 Creating a monitor mix

For live applications, audio engineers often send dierent mixes to the audience

and to the performing musicians. To allow this, the 1002B is equipped with a

dedicated monitor send bus. Each channel features a MON knob that sends a

“pre-fader” signal to the MON OUT jack, allowing the channel’s volume fader to

be adjusted without aecting the monitor mix. The signal can also be used as a

second eects send. Follow these steps to set up a basic monitor mix:

• Make sure the powered monitor speaker or power amp is turned o.

Connect a ¼" TS cable from the MON OUT jack to the powered speaker or

power amp

• Turn on the powered speaker or power amp, and then turn the volume up

about half way

• Turn the MON SEND knob to the center (12 o’clock) position. This setting may

need to be adjusted later depending on volume requirements

• As the musicians begin to play, turn each channel’s MON knob up slowly until

each source is audible in the monitor mix

• It may take some time to get a balanced mix that all the musicians are

happy with. If possible, avoid turning a channel’s MON knob much past the

center position. Do not point the monitor speakers directly at a microphone,

as this will likely cause feedback

See the Applications section for details.

As previously stated, the MON SEND jack can also be used as a second eects

send. This application requires a similar setup to the normal eects send, but

since the signal from each channel is sent pre-fader using the MON knob, signal.

Therefore, if you alter a channel’s volume during the performance, you must also

adjust that channel’s MON knob.

• NOTE: When using the MON SEND for eects, if you neglect to change a

channel’s MON knob while turning that channel’s volume fader all the

way down, you will still hear the eected signal coming through the mix.

This problem happens because the signal routes “pre-fader,” but the normal

FX SEND bus will not experience this issue

4.3 Battery installation

The 1002B can be powered by three 9V batteries. This feature allows you, for

example, to capture a high-quality recording while sitting on the beach with

your laptop. You’re no longer tethered by an electrical outlet. You can still record

with condenser mics thanks to the 18V of phantom power supplied by two of

the batteries. Follow these steps to install the batteries:

• Open the battery compartment located on the underside of the mixer.

You will need to remove a small screw with a Phillips screwdriver

• Slide the compartment cover out. There are slots for three batteries inside

the compartment

• Insert the batteries so that the + and – poles are in the correct position

• Replace the cover and tighten the screw

The battery power will last approximately four hours using high-quality

alkaline batteries.

5. Applications

Fig. 5.1: Field Recording

Fig. 5.2: Live Small Combo

UCA222

XENYX1002B

HPS5000

UL2000M

XENYX1002B

DI100

HPS5000

B212D

F1220A

MP3 Player

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx 1002B Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx 1002B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info