Bedienungsanleitung Behringer Xenyx 1202 (Seite 7 von 12) (Englisch)

496331

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

7 XENYX 1202/1002/802/502 User Manual

+4/-10

The stereo inputs of the XENYX 1202 and 1002 have an input sensitivity switch

which selects between +4 dBu and -10 dBV. At -10dBV (home-recording

level), the input is more sensitive (requires less level to drive it) than at +4 dBu

(studiolevel).

2.3 Connector panel and main section

2.3.1 Send/return eects path

Fig. 2.7: FX send/return connectors

Fig. 2.8: FX send/return controls

AUX RETURN

802 only: the STEREO AUX RETURN connectors are used to bring the output of

the external eects device (whoseinput is derived from the aux sends) back into

the console. You can instead use these connectors as additional inputs, but any

eects device will then have to be brought back into the console via a normal

stereo channel. This does, however, give you the ability to use the channel EQ on

the eects return signal if you wish.

◊ When using a stereo channel as effects return path, the FX control of

the relevant channel should generally be turned fully down to avoid

undesirable feedback.

If only the left connector is used, the AUX RETURN automatically operates in

mono. Use the AUX RETURN control to determine how much of the eects signal

is sent to the main mix.

FX SEND

The FX SEND output (does not apply for 502) should be connected to the input

of an external eects unit. The post-fader FX signal you created using the

input channel FX controls is sent to the eects unit via the FX SEND ouput.

Use the FXSEND control of the main section to adjust the overall send level

(1002and1202 only).

2.3.2 Monitor and main mix

PHONES/CONTROL ROOM

The stereo PHONES jack (at the top of the connector panel) is where you connect

headphones. The unbalanced CTRL ROOM OUT jacks carry the summed eects

and main mix signals, as well as soloed channel signals. The PHONES/CONTROL

ROOM control adjusts the level of both headphones and main monitor outputs.

The 502 is not equipped with control room outputs.

Fig. 2.9: Monitor/main mix connectors

MAIN MIX

The MAIN OUT connectors are unbalanced mono jacks. The main mix signal

appears here at a level of 0 dBu. The MAIN MIX fader adjusts the volume of these

outputs. The XENYX 802 and 502 mixing consoles feature a rotary control for

thispurpose.

Fig. 2.10: Monitor control and main mix fader

2.3.3 2-Track connectors

2-TRACK INPUT

The 2-TRACK INPUTs are used to bring an external signal source (e.g. CD player,

tape deck, etc.) into the console. They can also be used as a standard stereo line

input, so the output of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can

be connected.

Fig. 2.11: 2-Track input/output

Alternatively the line or tape output of a hi- amplier with source selection

switch could also be hooked up here, allowing you to easily listen to

additionalsources.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx 1202 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx 1202

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info