660464
11
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
11 XENYX QX1202USB/QX1002USB User Manual
3.2 Live sound
CLIP
SIG
L
R
XM8500
B215D Active Speakers
Bass Guitar
DI100
F1320D Active Monitors
MP3 Player
FX2000 Eects Processor
Portable
Digital
Recorder
Fig 3.2: Live performance with the QX1202USB
The above diagram shows some typical connections for a live performance using
the QX1202USB. Mono sources such as microphones and line-outs from guitar
preamps or DI boxes can be connected to channels 1-4 via XLR or ¼" cables.
Stereo sources can be connected to channels 5/6 through 11/12 via ¼" cables.
If an external eects processor is to be used instead of the onboard processor,
connect the FX SEND jack to the input of your processor. Turn the FX knob
up on each channel that you want to add eects to. Connect the outputs
(usuallystereo) from the processor to one of the stereo channels as shown
in the diagram. Make sure to leave the FX knob for this stereo channel fully
counterclockwise (o) to avoid feedback loops. Turn the LEVEL knob up on the
stereo channel receiving the processed signal to blend the eects into the mix.
Connect the MAIN OUTPUTS to active speakers or a power amplier. You may also
connect active oor monitors to the CONTROL ROOM OUTPUTS so the on-stage
talent can hear the mix. The 2-Track inputs can be used to connect an MP3
player for music between sets, and the 2-Track outputs can be used to connect a
digitalrecorder.
4. Installation
4.1 Mains connection
AC POWER IN
Connect the power supply to the 3-pin mains connector on the rear of the
console. Use the AC adapter supplied to connect the console to the mains.
Theadapter complies with all applicable safety standards.
Please use only the power supply unit provided with the console.
Never connect the XENYX to the power supply unit while the latter is
connected to the mains! First connect the console to the power supply
unit, then connect the power supply unit to the mains.
Please note that both the power supply unit and the mixing console
heat up considerably during operation. This is completely normal.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

behringer-xenyx-qx1002usb

Suche zurücksetzen

  • Wie kann man den Hall-Effekt aus- und einschalten? Eingereicht am 14-2-2023 11:18

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer Xenyx QX1002USB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer Xenyx QX1002USB

Behringer Xenyx QX1002USB Kurzanleitung - Deutsch, Englisch, Französisch, Portugiesisch, Spanisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info