Bedienungsanleitung Behringer Xenyx XL2400 (Seite 15 von 22) (Englisch)

660519

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

15 XENYX XL3200/XL2400/XL1600 User Manual

MON, AUX, GROUP, MAIN

These push-button switches (MON, AUX, GROUP and MAIN) determine to which

outputs and buses the talkback signal is to be routed. Then, turn on the talkbalk

microphone. Pressand hold down the push-button switch while speaking into

themicrophone.

5.6.2 SOLO

SOLO LEVEL

The SOLO LEVEL control adjusts the volume level of all solo signals routed to the

headphone and loudspeaker outputs.

PFL/AFL

Press the PFL/AFL switch to change the solo functionality from PFL mono

(pre-fader listen) to AFL stereo. The LED next to the switch indicates the selected

state. In PFL mode, the signal is tapped before the fader when pressing the solo

switch. In AFL mode, the signal is tapped behind the fader and in stereo for a

correct positioning within the stereo image.

If you adjust the signal's level with the TRIM control, select the PFL mode so that

the displayed level is not aected by the channel fader.

5.6.3 CD/TAPE

LEVEL

The LEVEL control adjusts the signal in the main mix, for example,

whenconnecting the CD/tape inputs to a CD player.

MAIN

Press the MAIN switch to route the CD signal to the main output. The CD signal

remains audible even when the MAIN MUTE switch is pressed. This allows you to

play music during performance breaks.

5.6.4 PHONES/SPEAKER section

The PHONES A/B control adjusts the volume level of the headphone output.

◊ IMPORTANT! High volume levels may damage your hearing and/or

your headphones/loudspeakers. To avoid switch-on/off thumps from

the console and any downstream devices, always make sure that the

power amp(s) or active speaker(s) are the last components that are

switched on and the first to be switched off. Always make sure that the

appropriate volume is set.

SPKR

The Speaker control adjusts the volume level of the SPEAKERS outputs.

SOURCE

The SOURCE push-button switch selects the signal source for the headphone

and loudspeaker outputs (main or CD/TAPE signal). Pressing a solo switch

routes the solo signal to these outputs and is not aected by the SOURCE

push-buttonswitch.

MAIN B section

The mixer sum can also be routed to the MAIN B output which may be connected

to a separate power amplier. This way the sum can be sent to multiple zones

and various loudspeaker groups (for example, center clusters and front lls).

Onemay also want to connect a stereo recording system for live recording.

LEVEL

The LEVEL control adjusts the volume level of the signal routed to the

MAINBoutput.

STEREO/MONO

The STEREO/MONO switch changes the Main B signal from mono to stereo

depending on the situation. For example, a mono signal is usually used for a

center cluster.

PRE/POST

The PRE/POST switch is used to determine whether the signal is tapped in front

or behind the MAIN A fader.

5.7 FX master section

This section has additional inputs for signals which do not require further signal

processing. Ideally, usethem for signals returning from external eects units.

This is why these inputs are referred to as FX returns. It is possible to route the

eect signals to the monitors and subgroups. This way the stereo channels can be

used for additional stereo signals, such as keyboards, etc., and not for eects

units' signals which require functions like fader, routing, solo and mute.

FX SEND

This is the master FX SEND control for adjusting the volume of all FX send signals

at the corresponding FX send jacks and at the inputs of the built-in eects

processor. Use it to control the master signal of all FX1/FX 2 signals from the

input channels. Whenneither of the FX SEND controls is turned up, theeects

processor will not receive a signal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL2400 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info