676633

BEKO Bari 91B Seite 23

23
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
- 23 -
appliances generated by other than an electrical source.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
•  We recommend the use of an air exhaust tube which has the
same diameter as the air exhaust outlet hole. If a pipe with a
smaller diameter is used, the efficiency of the product may
be reduced and its operation may become noisier.
Attention!
• Before proceeding with the installation, to be able to move the
hood more easily, complete the following operations:
1. Remove the anti-grease lterl by pulling the handle, as
shown in gure 2 - phase 1.
2. If the product is equipped with activated charcoal lters(B-
C), remove them as shown in gure 2 - phase 2B or 2C.
3. Unhook the small cupola M as shown in gure 2 - phase 4.
•Fixingtothewall(Fig.3):
- Mark the position of the lower side of the hood on the wall
gure 3 - phase 1(taking into account the minimum distance
required from the hob).
- Position the xing template on the wall, making sure that
the line coincides with the line previously made on the wall,
as described in the preceding section.
- Mark and drill xing holes gure 3 - phase 2.
- Fasten the 4 anchors and the 2 screws A-B without fully
tightening them gure 3 - phase 2.
- Position the appliance on the wall and permanently secure it
by pulling the 2 screws B gure 3 - phase 3-4 and the 2 locking
screws B gure 3 - phase 5.
- When carrying out the xing operations, use only screws
and screw anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard etc.).
- If the screws and screw anchors are supplied with the ap-
pliance, make sure that they are suited to the type of wall to
which the hood must be xed.
•FixingtothewallOPTIONAL ACCESSORIES (Fig.4):
This hood model can have optional levelling brackets which
can be requested from your dealer.
- Mark the position of the lower side of the hood on the wall
gure 3 - phase 1(taking into account the minimum distance
required from the hob).
- Position the xing template on the wall, making sure that
the line coincides with the line previously made on the wall,
as described in the preceding section.
- Mark and drill xing holes gure 3 - phase 2.
- Take the two levelling brackets C and fix them to the hood
support with the screws D as indicated in figure 4 - step 1. Do
not tighten the 2 levelling screws D.
- Take the appliance and hang it on the two screws B figure
4 - step 2.
- Align the appliance horizontally by adjusting the two levelling
screws D figure 4 - step 3.
- When you have finished the adjustment, tighten the 2 screws
B figure 4 - step 4 and mount the hood on the wall permanently
using the two safety screws B figure 4 - step 5.
- When carrying out the xing operations, use only screws
and screw anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard etc.).
If the screws and screw anchors are supplied with the appli-
ance, make sure that they are suited to the type of wall to
which the hood must be xed.
- Filtering version
- Unhook the small cupola M and remove the grille E (Fig. 5).
- Pass the power supply cable through the slots of the small
cupola M as shown in Fig. 6.
- Take the fairlead H and position it between the power sup-
ply cable and the slot.
- Fasten the small cupola M and the grille E making sure that
is it perfectly hooked on to the fastening pins G. (Fig. 6).
The filters must be applied to the suction unit positioned inside
the hood. They must be centred by turning them 90 degrees
until the stop catch is tripped (Fig.10B).
•Optionalaccessories
This model may have decorative ducts as optional accessories
- ask your retailer for information.
Before installing decorative ues it is necessary to remove the
small cupola and loosen the 4 screws B that lock the fastening
pins G as shown in Fig.7.
•Installationofmodelswithdecorativeducts-extrac-
tor hood
Make sure the electrical power supply is within the measure-
ments of the decorative connector.
Connect ange F to the air exhaust hole using exible hose
L (Fig.7).
Adjust the width of the support bracket of the top connector
(Fig. 8). Then x it to the ceiling so that it is on the same axis
as the hood using screws A and observing the distance from
the ceiling shown in (Fig. 8). Slide the top connector inside
the lower duct and place this on the body (Fig. 9).
Pull out the top duct as far as the bracket and secure it using
screws B (Fig. 8).
To transform the hood from a ducting version into a ltering
version, ask your dealer for the charcoal lters and follow the
installation instructions.
•Filterhood:
Please note:
- In order to transform the hood from EXTRACTOR HOOD
into FILTER HOOD the active carbon filters must be ordered
at your distributor as accessory.
We have 3 different types of Kit, one with non-regenerable
active carbon filters (Fig.10B) and the other one with regen-
erable active charcoal filters (washable) (Fig.10C - Fig.10D).
- Depending on the model one owns, the CIRCULAR active
carbon filters must be applied to the suction unit located
inside the hood, centring them and rotating them by 90
degrees until they snap into place (Fig.10B), to replace them
perform the operation in reverse order.
- For WASHABLE regenerable activated carbon filters
(Fig.10C), follow the assembly instructions contained in
the KIT.
- For the WASHABLE CIRCULAR regenerable active carbon
filters (Fig.10D), remove the pad and follow the instructions in
the USE AND MAINTENANCE paragraph, "regenerable active
carbon filters".
USE AND MAINTENANCE
•  We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air. The effective
performance of the cooker hood depends on constant main-
tenance; the anti-grease filter and the active carbon filter both
require special attention.
•Theanti-greasefilter is responsible retaining the grease
particles suspended in the air, therefore it is subject to clogging
with variable frequency according to the use of the appliance.
… 23 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BEKO Bari 91B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info