Bedienungsanleitung BEKO CWB9930X (Seite 29 von 88) (Alle Sprachen)

676961

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

- 27 -

ductor used to circulate hot air or for evacuating fumes from

other appliances generated by other than an electrical source.

Before proceeding with the assembly operations, remove the

anti-grease filter(s) (Fig.2.2 - Fig.3.2) so that the unit is easier to

handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

• If the appliance is supplied with the small cupola M remove

it by releasing it as indicated in Fig.2.3 - Fig.3.3.

Before proceeding with the assembly operations, for easier

manoeuvrability of the appliance disengage the anti-grease

lter by pulling handle B as indicated in Fig.2.2 - Fig.3.2.

If one owns a model with perimeter suction panel, before

carrying out this operation, perform the following phases:

- Open panel C as indicated in Fig.2.1 - Fig.3.1.

- If one owns the version with three A panels release them from

the xing pins by pulling outwards (Fig.3.4) and then remove

them from safety pins N (Fig.3.4) placed inside the hood. To

put them back perform the operation in reverse order.

ATTENTION! During this disassembly and assembly

operation ensure to hold the panel securely to prevent

accidental falls.

• Wall mounting:

Trace the bottom side of the hood on the wall. Consider the

measurements shown in Fig.4A and minimum distance from

the cooking surface (Fig.4B).

- Position the xing template on the wall, making sure that the

line coincides with the line previously made on the wall.

- Mark the xing holes and cut them into the material (Fig.5).

- Fix the 2 top screws K and screw anchors (Fig.5), without

tightening them completely.

- Place the appliance against the wall, align it in horizontal

position and tighten screws K (Fig.6A).

- Once the adjustment has been completed, x the hood using

the 2 screws C (Fig.6B).

- When carrying out the xing operations, use only screws

and screw anchors suited to the type of wall (e.g. reinforced

concrete, plasterboard etc.).

- If the screws and screw anchors are supplied with the

appliance, make sure that they are suited to the type of wall

to which the hood must be xed.

•Installationofmodelswithoutdecorativeducts:

Extractorhood

- Unclip the canopy M and remove the grille E (Fig.7).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.9A.1.

- Taking the grommet H, position it between the power cable

and the slot (Fig.9A.2).

- Connect the exible hose L (not supplied) to the hood (Fig.9B).

- Re-position the small cupola M paying attention that it is

hitched perfectly to the xing pins G (Fig.9B).

• Filtering version:

- Unclip the canopy M and remove the grille E (Fig.7).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.8.1.

- Taking the grommet H, position it between the power cable

and the slot (Fig.8.2).

- Fix the small cupola M and the grille E making sure that is it

perfectly hooked on to the fastening pins G (Fig.8).

• Optional accessories:

This model may have decorative ducts as optional accessories

- ask your retailer for information.

Before installing decorative ues it is necessary to remove

the small cupola M and loosen the 4 screws Q that lock the

fastening pins G as shown in Fig.11.

•Installationofmodelswithdecorativeducts:

Extractorhood

Make sure the electrical power supply is within the measure-

ments of the decorative connector. Adjust the width of the

support bracket of the top connector (Fig.10.2). Then x it

to the ceiling so that it is on the same axis as the hood using

screws A and observing the distance from the ceiling shown in

Fig.10.1. Connect ange F to the air exhaust hole using exible

hose L (Fig.12A). Slide the top connector inside the lower duct

and place this on the body (Fig.12B). Pull out the top duct as

far as the bracket and secure it using screws B (Fig.10.2). To

transform the hood from a ducting version into a ltering

version, ask your dealer for the charcoal lters and follow the

installation instructions.

•Filterhood:

Please note:

The lters must be ordered from your dealer as an accessory.

- To transform the hood from the SUCTION version to the

FILTERING version, charcoal lters must be ordered from your

dealer as an accessory. Two types of kit are available, one with

non-renewable lters (Fig.13) and the other with renewable

lters (washable) (Fig.14). Unlike traditional carbon lters,

this carbon lter can be washed and reactivated for approxi-

mately 12-15 times. With normal hood use, this lter should

be cleaned once every 2-3 months. The lter can be washed

into a dishwasher at the highest temperature using a standard

dishwasher detergent. After washing, dry the lter in the oven

at 100°C for 10-15 minutes to reactivate it. The lter will retain

its odour-absorbing capacity for three years, after which it will

have to be replaced.

- If a bracket is found in the packaging like that indicated in

Fig.14 loosen the screws already installed inside the hood and

install the bracket using the previously-removed screws.

- To replace re-usable carbon filters Y, remove the brackets

from their seat, pulling them outwards (Fig.14).

- If your product is not supplied with the bracket, it means that

the active charcoal lter cannot be renewed (Fig.13). These

must be applied to the suction unit inside the hood, centring

them in it and turning them 90° until they snap into place

(Fig.13).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The effective performance of the cooker hood depends on

constant maintenance; the anti-grease filter and the active

carbon filter both require special attention.

•Theanti-greasefilter is responsible retaining the grease

particles suspended in the air, therefore it is subject to clogging

with variable frequency according to the use of the appliance.

- To prevent the danger of possible fires, at least every 2

months one must wash the anti-grease filters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Theactivecarbonfilters are used to purify the air that is

BEKO CWB9930X Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info