Bedienungsanleitung BEKO DC 1560 (Seite 34 von 72) (Englisch)

75063

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

34 - EN

5 Maintenance and cleaning

Cover filter

Lint and fibres released from the laundry to the

air during the drying cycle are collected in the

“Cover Filter”.

C Such fibre and lint are generally formed

during wearing and washing.

C Always clean the filter after each drying

process.

C You can clean the filter and filter area by

vacuum cleaner.

To clean the filter:

1. Open the loading door.

2. Remove the cover filter by pulling it up and

open the filter.

3. Clean lint, fibre, and cotton raveling by hand

or with a soft piece of cloth.

4. Close the filter and place it back into its seat.

CClogging may arise on the filter surface after

using your machine for some time; if this

occurs, wash the filter with water and dry it

before using again.

Sensor (models with a sensor)

There are humidity sensors in your dryer that

detect whether the laundry is dry or not.

To clean the sensor:

1. Open the loading door of the dryer.

2. Allow the machine to cool down if drying has

been carried out.

3. Wipe the metal sensors with a soft cloth,

dampened with vinegar and dry them.

C Clean metal sensors 4 times a year.

A Never use solvents, cleaning agents or

similar substances when cleaning since these

materials can cause fire and explosion!

Water tank (Products equipped with a

condenser);

The moisture in the damp laundry is taken from

the laundry and condensed. Drain the water

tank after each drying cycle or during drying

when “Water tank” warning light turns on.

CYou can use the water in the water tank in

your steam irons or air humidifiers.

A Condensed water is not drinkable!

A Never take out the water tank when the

programme is running!

Water tank may be located in two different

places as indicated below, depending on the

model of your dryer.

- Inside the drawer on the panel

- Behind the kick plate cover

If you forget to drain the water tank, your dryer

will stop during the following drying cycles

when the water tank is full and the “Water tank”

warning light will turn on. If this is the case, press

the “Start/Pause/Cancel” button to resume the

drying cycle after draining the water tank.

To drain the water tank:

1. Carefully remove the water tank by opening

the kick plate cover/pulling the drawer.

2. Drain the water by opening the water tank

cover.

3. If there is lint accumulation in the water tank

cover, clean it and press to close.

4. Place the water tank into its seat.

For the condenser (products with a

condenser)

Hot and humid air in the condenser is cooled

with the cold air from the room. Thus, the humid

air circulating in your dryer is condensed and

then pumped into the tank.

CClean the condenser after every 15 drying

cycles or once a month.

To clean the condenser:

1. If a drying process has been carried out, open

the door of the product and wait until it cools

down.

2. Unlock the 4 condenser locks after opening

the kick plate.

3. Pull out the condenser.

4. Clean the condenser with pressurized water

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DC 1560 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DC 1560

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info