Bedienungsanleitung BEKO DH 8433 RXM (Seite 42 von 60) (Deutsch, Englisch)

676675

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

42 / EN

Dryer / User Manual

3 Installaton

Before the calling the nearest Authorized

Service for the installation of the dryer,

ensure that electrical installation and water

drain is appropriate referring to the user’s

manual. (See 3.3 Connecting to the

drain and 3.5 Electrical connection) If

they are not suitable, contact a qualified

electrician and technician to make necessary

arrangements.

Preparation of the dryer's location

as well as the electrical and

waste water installations is under

customer's responsibility.

Prior to installation, visually check

if the dryer has any defects on it. If

the drier is damaged, do not have it

installed. Damaged products cause

risks for your safety.

Let your dryer wait for 12 hours

before starting to use it.

3.1 Appropriate installation

location

Install the dryer on a stable and level surface.

Dryer is heavy. Do not move it by yourself.

• Operate your dryer in a well ventilated,

dust-free environment.

• The gap between the dryer and the

surface should not be reduced by the

materials such as carpet, wood and tape.

• Do not cover the ventilation grills of the

dryer.

• There must not be a lockable, sliding or

hinged door that may block the opening

of the loading door in the place where

your dryer is to be installed.

• Once the dryer is installed, it should stay

at the same place where its connections

have been made. When installing the

dryer, make sure that its rear wall does

not touch anywhere (tap, socket, etc.).

• Place the dryer at least 1 cm away from

the edges of other furniture.

• Your dryer can be operated at

temperatures between +5°C and +35°C.

If the operating conditions fall outside

of this range, operation of the dryer

will be adversely affected and it can get

damaged.

• The rear surface of the tumble dryer

shall be placed against a wall.

Do not place the dryer on the power

cable.

3.2 Removing the

transportation safety

assembly

Remove the transportation safety

assembly before using the dryer for

the first time.

• Open the loading door.

• There is a nylon bag inside the drum that

contains a piece of styrofoam. Hold it

from its section marked with XX XX.

• Pull the nylon towards yourself and

remove the transportation safety

assembly.

Check that no part of the

transportation safety assembly

remains inside the drum.

3.3 Connecting to the drain

In products equipped with condenser

unit, water accumulates in the water tank

during the drying cycle. You should drain

accumulated water after each drying cycle.

You can directly drain accumulated water

through the water drain hose supplied with

the product instead of periodically draining

the water collected in the water tank.

Connecting the water drain hose

1-2 Pull hose at the behnd of the dryer

by hand n order to dsconnect t from

where t s connected. Do not use any

tools to remove the hose.

3 Connect one end of the dran hose

suppled wth the dryer to the

connecton pont from where you

removed the hose of the product n

prevous step.

4 Connect the other end of the dran hose

drectly to the wastewater dran or to

the washbasn.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DH 8433 RXM Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DH 8433 RXM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info