Bedienungsanleitung BEKO DH8534 RX0 (Seite 43 von 64) (Deutsch, Englisch)

676684

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

43 / EN

Dryer / User Manual

3 Installaton

Before the calling the nearest Authorized

Service for the installation of the dryer, en-

sure that electrical installation and water

drain is appropriate referring to the user’s

manual. (See 3.3 Connecting to the drain

and 3.5 Electrical connection) If they are

not suitable, contact a qualied electrician

and technician to make necessary arrange-

ments.

Preparation of the dryer's location

as well as the electrical and waste

water installations is under cus-

tomer's responsibility.

Prior to installation, visually check

if the dryer has any defects on

it. If the drier is damaged, do not

have it installed. Damaged prod-

ucts cause risks for your safety.

Let your dryer wait for 12 hours

before starting to use it.

3.1 Appropriate installation

location

Install the dryer on a stable and level surface.

Dryer is heavy. Do not move it by yourself.

• Operate your dryer in a well ventilated,

dust-free environment.

• The gap between the dryer and the

surface should not be reduced by the

materials such as carpet, wood and tape.

• Do not cover the ventilation grills of the

dryer.

• There must not be a lockable, sliding or

hinged door that may block the opening

of the loading door in the place where

your dryer is to be installed.

• Once the dryer is installed, it should stay

at the same place where its connections

have been made. When installing the

dryer, make sure that its rear wall does

not touch anywhere (tap, socket, etc.).

• Place the dryer at least 1 cm away from

the edges of other furniture.

• Your dryer can be operated at

temperatures between +5°C and +35°C.

If the operating conditions fall outside

of this range, operation of the dryer

will be adversely affected and it can get

damaged.

• The rear surface of the tumble dryer

shall be placed against a wall.

Do not place the dryer on the

power cable.

3.2 Removing the

transportation safety

assembly

Remove the transportation safety

assembly before using the dryer

for the rst time.

• Open the loading door.

• There is a nylon bag inside the drum that

contains a piece of styrofoam. Hold it

from its section marked with XX XX.

• Pull the nylon towards yourself and

remove the transportation safety

assembly.

Check that no part of the trans-

portation safety assembly re-

mains inside the drum.

3.3 Connecting to the drain

In products equipped with condenser unit,

water accumulates in the water tank during

the drying cycle. You should drain accumu-

lated water after each drying cycle.

You can directly drain accumulated water

through the water drain hose supplied with

the product instead of periodically draining

the water collected in the water tank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DH8534 RX0 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DH8534 RX0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info