Bedienungsanleitung BEKO DIN15C20 (Seite 34 von 47) (Englisch)

762748

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

34/EN

Adjusting the amount of rinse

aid

1. After turning on your machine, press

and hold the Time Delay and Start /

Pause / Cancel keys respectively.

2. Using the Time Delay key, turn on the 6

LED.

3. You can use the function keys to adjust

the rinse aid level.

If the 1st programme indicator is on, no

rinse aid will be dispensed

If the 2nd programme indicator is on, 1

dose of rinse aid will be dispensed.

If the 3rd programme indicator is on, 2

doses of rinse aid will be dispensed.

If the 4th programme indicator is on, 3

doses of rinse aid will be dispensed.

If the 1st, 2nd, 3rd and 4th programme

indicators are on, 4 doses of rinse aid will

be dispensed.

4. Press the On/Off key to exit the

settings menu. Your setting will be

saved automatically.

Rinse Aid Indicator ( )

Please check the rinse aid indicator on the

display to see whether there is adequate

amount of rinse aid in the dishwasher or

not. You need to refill the rinse aid reservoir

with rinse aid whenever rinse aid indicator

appears on the display of your machine.

End of programme

When the programme you have

selected comes to an end, an audible

warning signal will warn you to turn off

your machine. This audible signal will

warn you with certain intervals before it

turns off.

Start / Pause indicator will go off once the

washing programme has ended.

1. Open the door of the machine.

2. Press the On/Off key to switch off your

machine.

3. Close the tap.

4. Unplug the machine from the socket.

For energy saving, the machine is

automatically switched off following the

completion of the programme or when

the programme is not started.

Leave your dishes in the machine

for about 15 minutes after they are

washed in order to have them cooled.

Your dishes will dry in a shorter time

if you leave the door of your machine

ajar during this period. This process

will increase the drying effectiveness of

your machine.

Water Cut-off Warning

If mains water is cut off or water inlet tap

is turned off, the machine will not take

water in and water off indicator will flash.

As long as the problem continues, washing

programme is paused and the water inlet

is checked regularly by the machine; when

the water is restored water off indicator will

disappear after a while and the washing

programme resumes.

Overflowing Warning

If the machine intakes too much water or

there is leakage at any of the components

then the machine will detect this and

water overflow indicator will flash on the

Programme indicator. As long as the

overflowing continues the safety algorithm

will be active and try to discharge the water.

If overflowing stops and safety is assured,

water overflow indicator will disappear. If

the indicator does not disappear, there is a

permanent fault. In this case the authorised

service should be contacted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DIN15C20 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DIN15C20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info