Bedienungsanleitung BEKO DPS 7343 X (Seite 40 von 56) (Englisch, Holländisch)

579372

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

40 / 56 EN

Dryer / User Manual

3 Installation

Before the calling the nearest Authorized Service for the

installation of the dryer, ensure that electrical installation

and water drain is appropriate referring to the user's

manual.(See 3.3 Connecting to the drain and 3.5

Electrical connection) If they are not suitable, contact

a qualified electrician and technician to make necessary

arrangements.

Preparation of the dryer's location

as well as the electrical and waste

water installations is under customer's

responsibility.

Prior to installation, visually check if the

dryer has any defects on it. If the drier

is damaged, do not have it installed.

Damaged products cause risks for your

safety.

Let your dryer wait for 12 hours before

starting to use it.

3.1 Appropriate installation location

Install the dryer on a stable and level surface.

Dryer is heavy. Do not move it by yourself.

• Operate your dryer in a well ventilated, dust-free

environment.

• The gap between the dryer and the surface should

not be reduced by the materials such as carpet,

wood and tape.

• Do not cover the ventilation grills of the dryer.

• There must not be a lockable, sliding or hinged

door that may block the opening of the loading

door in the place where your dryer is to be

installed.

• Once the dryer is installed, it should stay at the

same place where its connections have been

made. When installing the dryer, make sure that

its rear wall does not touch anywhere (tap, socket,

etc.).

• Place the dryer at least 1 cm away from the edges

of other furniture.

• Your dryer can be operated at temperatures

between +5°C and +35°C. If the operating

conditions fall outside of this range, operation of

the dryer will be adversely affected and it can get

damaged.

• The rear surface of the tumble dryer shall be

placed against a wall.

Do not place the dryer on the power

cable.

3.2 Removing the transportation

safety assembly

Remove the transportation safety

assembly before using the dryer for the

first time.

• Open the loading door.

• There is a nylon bag inside the drum that contains

a piece of styrofoam. Hold it from its section

marked with XX XX.

• Pull the nylon towards yourself and remove the

transportation safety assembly.

Check that no part of the transportation

safety assembly remains inside the drum.

3.3 Connecting to the drain

In products equipped with condenser unit, water

accumulates in the water tank during the drying cycle.

You should drain accumulated water after each drying

cycle.

You can directly drain accumulated water through the

water drain hose supplied with the product instead of

periodically draining the water collected in the water

tank.

Connecting the water drain hose

1-2 Pull hose at the behind of the dryer by hand in

order to disconnect it from where it is connected.

Do not use any tools to remove the hose.

3 Connect one end of the drain hose supplied with

the dryer to the connection point from where you

removed the hose of the product in previous step.

4 Connect the other end of the drain hose directly to

the wastewater drain or to the washbasin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DPS 7343 X Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DPS 7343 X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info