Bedienungsanleitung BEKO DV 2570 X (Seite 5 von 72) (Deutsch, Englisch, Französisch)

77361

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

5 - EN

2 Installation

Refer to the nearest Authorised Service

Agent for installation of your product.

CPreparation of location and electrical

installation for the product is under

customer’s responsibility.

BInstallation and electrical connections

must be carried out by a qualified

personnel.

APrior to installation, visually check if

the product has any defects on it. If

so, do not have it installed. Damaged

products will cause risks for your

safety.

Appropriate installation locati-

• Install the product in an environment

which has no risk of freezing and is in a

stable and level position.

• Operate your product in a well

ventilated, dust-free environment.

• Do not block the air ducts in front of

and under the product with materials

such as long pile rugs and wooden

bands.

• Do not place your product on a long

pile rug or on similar surfaces.

• Do not install the product behind a

door with a lock, sliding door or a

hinged door which can strike the

product.

• Once the product is installed, it should

stay at the same place where its

connections have been made. When

installing the product, make sure

that the rear wall of it does not touch

anywhere (tap, socket, etc.) and also

pay attention to install the product at a

place where it will stay permanently.

BDo not place the product on top of the

power cable.

• Keep at least 1.5 cm distance to walls

of other furniture.

Under counter installation

• A special part (Part no: 295 970 0100)

replacing the top trim must be provided

and installed by the Authorised Service

Agent in order to use the machine

under a counter or in a cupboard. It

should never be operated without the

top trim.

• Leave at least 3 cm of space between

the side and rear walls of the product

and the walls of the counter/cupboard

when installing your product under a

counter or in a cupboard.

Mounting over a washing mac-

hine

• A fitting device should be used

between the two machines when

installing above a washing machine.

The bracket (Part no. 296 280 0100

white/296 280 0200 grey) must be

installed by the Authorised Service

Agent.

• Place the product on a firm floor. If

it will be placed on top of a washing

machine, the approximate weight of

both machines may reach 180 kg when

they are full. Therefore, the floor must

be capable of carrying the load on it!

Ventilation hose and connecti-

on (for products equipped with

an outlet vent)

Ventilation hose allows exhaust air from

inside the machine

Vented dryer has 1 air outlet.

Stainless sheet metal or aluminum pipes

can be used instead of a hose. The pipe

diameter should be minimum 10 cm.

Maximum hose and pipe lengths are

given in the table below.

Hose Pipe

Maximum length

4 m 5 m

1 elbow 45°

-1.0 m -0.3 m

1 elbow 90°

-1.8 m -0.6 m

1 elbow 90° short

-2.7 m

1 wall passage

-2.0 m -2.0 m

CEach elbow and other passages should

be subtracted from the maximum

length stated above.

To connect a ventilation hose;

1. Connect the air outlet hose to the

hose spacer piece by turning it

counterclockwise.

2. Make the hose passages as shown

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DV 2570 X Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DV 2570 X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info