Bedienungsanleitung BEKO HBG70 (Seite 16 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

556806

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 16 -

applicable for external air evacuation.

Before connecting the model to the electricity network:

- Control the data plate (positioned inside the appliance)

to ascertain that the voltage and power correspond to the

network and the socket is suitable. If in doubt ask a qualied

electrician.

- If the power supply cable is damaged, it must be replaced

with another cable or a special assembly, which may be

obtained direct from the manufacturer or from the Technical

Assistance Centre.

- This device must be connected to the mains supply through

either a plug fused 3A or hardwired to a 2 phase spur pro-

tected by 3A fuse.

2. Warning!

In certain circumstances electrical appliances may be a

danger hazard.

A) Do not check the status of the filters while the cooker

hood is operating.

B) Do not touch bulbs or adjacent areas, during or straight

after prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker

hood.

D) Avoid free flame, as it is damaging for the filters and

a fire hazard.

E) Constantly check food frying to avoid that the

overheated oil may become a fire hazard.

F) Disconnect the elec trical plug prior to any

maintenance.

G) This appliance is not intended for use by young children

or infirm persons without supervision.

H) Young children should be supervised to ensure they do

not play with the appliance.

I) There shall be adequate ventilation of the room when the

rangehood is used at the same time as appliances burning

gas or other fuels.

L) There is a risk of fire if cleaning is not carried out in

accordance with the instructions.

This appliance conforms to the European Directive EC/2002/96,

Waste Electrical and Electronic Equipment (WEEE). By making

sure that this appliance is disposed of in a suitable manner,

the user is helping to prevent potential damage to the

environment or to public health.

The symbol on the product or on the accompanying

paperwork indicates that the appliance should not be treated

as domestic waste, but should be delivered to a suitable

electric and electronic appliance recycling collection point.

Follow local guidelines when disposing of waste. For more

information on the treatment, re-use and recycling of this

product, please contact your local authority, domestic waste

collection service or the shop where the appliance was

purchased.

INSTALLATION INSTRUCTIONS

•Assemblyandelectricalconnectionsmustbecarriedout

by specialised personnel.

•Wear protective gloves before proceeding with the

installation.

•ElectricConnection

Note: Verify the data label placed inside the appliance:

- If the symbol appears on the plate, it means that no earth

connection must be made on the appliance, therefore follow

the instructions concerning insulation class II.

- If the symbol DOES NOT appear on the plate, follow the

instructions concerning insulation class I.

Insulation class II

The appliance has been manufactured as a class II, therefore

no earth cable is necessary.

The plug must be easily accessible after the installation of

the appliance. If the appliance is equipped with power cord

without plug, a suitably dimensioned omnipolar switch

with 3 mm minimum opening between contacts must be

tted between the appliance and the electricity supply in

compliance with the load and current regulations.

The connection to the mains is carried out as follows:

BROWN = L live wire

BLUE = N neutral

Insulation class I

This is a class I, appliance and must therefore be connected

to an eecient earthing system.

The appliance must be connected to the electricity supply

as follows:

BROWN = L live wire

BLUE = N neutral

YELLOW/GREEN = earth

The neutral wire must be connected to the terminal with the

N symbol while the YELLOW/GREEN, wire must be connected

to the terminal by the earth symbol .

Warning:

When connecting the appliance to the electricity supply, make

sure that the mains socket has an earth connection. After tting

the ducted cooker hood, make sure that the electrical plug is

in a position where it can be accessed easily. If the appliance

is connected directly to the electricity supply, an omnipolar

switch with a minimum contact opening of 3 mm must be

placed in between the two; its size must be suitable for the load

required and it must comply with current legislation.

•The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm. If a connection tube

composed of two parts is used, the upper part must be placed

outside the lower part. Do not connect the cooker hood

exhaust to the same conductor used to circulate hot air or for

evacuating fumes from other appliances generated by other

than an electrical source.

Before proceeding with the assembly operations, remove the

anti-grease lter(s) (Fig.7) so that the unit is easier to handle.

In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•We recommend the use of an air exhaust pipe with a

diameter of 150. If a pipe with a smaller diameter is used, the

eciency of the product may be reduced and its operation

may become noisier.

Please note:

If your version of the appliance has decorative glass before

installing the hood, carry out the following steps as shown

in gure 4:

1 - Remove both the cooker hood body B and the glass

panel A from the packaging and place them horizontally on

a secure surface.

2 - Take the glass panel A and position it above the cooker

hood body B.

3 - Fix the glass panel securely to the cooker hood body using

BEKO HBG70 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info