Bedienungsanleitung BEKO HNS61210XH (Seite 11 von 80) (Alle Sprachen)

676916

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

• The hood must NEVER be used as a support surface unless

specifically indicated.

• Use only the fixing screws supplied with the product for in-

stallation or, if not supplied, purchase the correct screws type.

• Use the correct length for the screws which are identified in

the Installation Guide.

• In case of doubt, consult an authorized service assistance

center or similar qualified person.

WARNING!

• Failure to install the screws or fixing device in accor-

dance with these instructions may result in electrical

hazards.

• Do not use with a programmer, timer, separate remote

control system or any other device that switches on

automatically.

• This appliance is marked according to the European directi-

ve 2012/19/EC on Waste Electrical and Electronic Equipment

(WEEE).

• By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the envi-

ronment and human health, which could otherwise be caused

by inappropriate waste handling of this product.

• The symbol

on the product, or on the documents

accompanying the product, indicates that this appliance may

not be treated as household waste. Instead it should be taken

to the appropriate collection point for the recycling of electrical

and electronic equipment. Disposal must be carried out in

accordance with local environmental regulations for waste

disposal.

• For further detailed information regarding the process, col-

lection and recycling of this product, please contact the ap-

propriate department of your local authorities or the local de-

partment for household waste or the shop where you purcha-

sed this product.

Appliance designed, tested and manufactured according to:

• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC

62233.

• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO

5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3;

ISO 3741; EN 50564; IEC 62301.

• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;

EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a

correct use in order to reduce the environmental impact:

Switch ON the hood at minimum speed when you start coo-

king and kept it running for few minutes after cooking is fini-

shed. Increase the speed only in case of large amount of

smoke and vapor and use boost speed(s) only in extreme

situations. Replace the charcoal filter(s) when necessary to

maintain a good odor reduction efficiency. Clean the grease

filter(s) when necessary to maintain a good grease filter effi-

ciency. Use the maximum diameter of the ducting system

indicated in this manual to optimize efficiency and minimize

noise.

Use

The hood is designed to be used either for exhausting or filter

version.

Ducting version

The cooker hood has an upper air duct B1 and an optional

rear air duct B2*, for external fumes exit.

Select the suitable air duct and apply the flange C supplied,

ensure to close the unused hole duct with cap D* supplied if

provided.

Note: in some models upper hole B1 is supplied closed:

Press firmly to detach the detachable part that closes the

outlet hole and remove it.

Attention! The detachable part cannot be mounted in

position again. Carry out this operation only if you are sure

of the type of installation to make.

Caution! In some models the rear hole duct is not easily ac-

cessible, even when the tap (if mounted) is removed, in this

case remove the plastic piece E1 or E2 that is blocking the

hole duct, by unwinding using pliers and cutter. Check that

the filter/suction selector (inside the cooker hood) G is in the

suction (A) position.

Filter version

In the case where it is not possible to discharge the cooking

fumes externally, the cooker hood may be used in the filter

version by fixing a carbon filter, the fumes and vapours are

recycled via the anterior grill placed above the control panel.

Check that the filter/suction selector (inside the cooker ho-

od) G is in the filter (F) position.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the ran-

ge hood must be not less than 60cm from electric cookers and

75cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a gre-

ater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating indica-

ted on the plate situated inside the hood. If provided with a

plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after installa-

tion. If it not fitted with a plug (direct mains connection) or if

the plug is not located in an accessible area, after installation,

apply a double pole switch in accordance with standards

which assures the complete disconnection of the mains under

conditions relating to over-current category III, in accordance

with installation instructions.

WARNING!

Before re-connecting the hood circuit to the mains supply and

checking the efficient function, always check that the mains

cable is correctly assembled.

Warning! If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly qualified

persons in order to avoid hazard.

BEKO HNS61210XH Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info