Bedienungsanleitung BEKO WCC 7632 XS (Seite 5 von 20) (Englisch)

676622

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

5 / EN

Washing Machine / User’s Manual

1.6 Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product

bears a classification symbol for waste electrical and electronic equipment

(WEEE).

This product has been manufactured with high quality parts and materials

which can be reused and are suitable for recycling. Do not dispose of the

waste product with normal domestic and other wastes at the end of its servi-

ce life. Take it to the collection center for the recycling of electrical and elec-

tronic equipment. Please consult your local authorities to learn about these

collection centers.

Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It

does not contain harmful and prohibited materials specified in the Directive.

2 Installation

Refer to the nearest Authorised Service Agent for installation

of the product. To make the product ready for use, review

the information in the user manual and make sure that the

electricity, tap water supply and water drainage systems are

appropriate before calling the Authorized Service Agent. If

they are not, call a qualified technician and plumber to have

any necessary arrangements carried out.

Preparation of the location and electrical, tap water and

waste water installations at the place of installation is

under customer's responsibility.

Make sure that the water inlet and discharge hoses

as well as the power cable are not folded, pinched or

crushed while pushing the product into its place after

installation or cleaning procedures.

WARNING: Installation and electrical connections

of the product must be carried out by the Authorized

Service Agent. Manufacturer shall not be held liable for

damages that may arise from procedures carried out by

unauthorized persons.

WARNING: Prior to installation, visually check if

the product has any defects on it. If so, do not have it

installed. Damaged products cause risks for your safety.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a

long pile rug or similar surfaces.

• Total weight of the washing machine and the dryer -with

full load- when they are placed on top of each other

reaches to approx. 180 kilograms. Place the product

on a solid and flat floor that has sufficient load carrying

capacity!

• Do not place the product on the power cable.

• Do not install the product at places where temperature

may fall below 0ºC.

• Place the product at least 1 cm away from the edges of

other furniture.

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging

reinforcement. Remove the packaging reinforcement by

pulling the ribbon.

2.3 Removing the transportation locks

WARNING: Do not remove the transportation locks

before taking out the packaging reinforcement.

WARNING: Remove the transportation safety bolts

before operating the washing machine! Otherwise, the

product will be damaged.

1. Loosen all the bolts with a suitable spanner until they

rotate freely

(C).

2. Remove transportation safety bolts by turning them

gently.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WCC 7632 XS Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info