Bedienungsanleitung BEKO WI1483 (Seite 12 von 52) (Englisch)

556766

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

12 / EN

Washing Machine /User’s Manual

Installation

Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needs to be moved again in the future.

Never move the product without the

transportation safety bolts properly fixed in

place!

3.4 Connecting water supply

The water supply pressure required to run

the product is between 1 to 10 bars (0.1 – 1

MPa). It is necessary to have 10 – 80 liters of

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

If you are going to use the double water-inlet

product as a single

(cold) water-inlet unit,

you must install the supplied stopper to the

hot water valve before operating the product.

(Applies for the products supplied with a blind

stopper group.)

WARNING: Models with a single water inlet

should not be connected to the hot water tap.

In such a case the laundry will get damaged or

the product will switch to protection mode and

will not operate.

WARNING: Do not use old or used water

inlet hoses on the new product. It may cause

stains on your laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose (left) (max. 90 ºC) is for hot water inlet,

blue hose (right) (max. 25 ºC) is for cold water

inlet.

WARNING: Ensure that the cold and hot

water connections are made correctly when

installing the product. Otherwise, your laundry

will come out hot at the end of the washing

process and wear out.

2. Tighten all hose nuts by hand. Never use a tool

when tightening the nuts.

3. Open the taps completely after making the

hose connection to check for water leaks at

the connection points. If any leaks occur, turn

off the tap and remove the nut. Retighten the

nut carefully after checking the seal. To prevent

water leakages and damages caused by them,

keep the taps closed when the machine is not

in use.

3.5 Connecting to the drain

•Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

•Drainhoseshallbeattachedtoawalldrain,

stand pipe or sink siphon connected to the foul

water drain, do not connect to surface water

drains.

WARNING: Your house will be flooded if

the hose comes out of its housing during

water discharge. Moreover, there is risk of

scalding due to high washing temperatures!

To prevent such situations and to ensure

smooth water intake and discharge of the

machine, fix the end of the discharge hose

tightly so that it cannot come out.

•Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

•Incasethehoseiselevatedafterlayingiton

the floor level or close to the ground (less than

40 cm above the ground), water discharge

becomes more difficult and the laundry may

come out excessively wet. Therefore, follow the

heights described in the figure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WI1483 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info