556826
7
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
7
EN
3 Installation
Refer to the nearest Authorised Service
Agent for installation of the product. To
make the product ready for use, review
the information in the user manual and
make sure that the electricity, tap water
supply and water drainage systems are
appropriate before calling the Authorized
Service Agent. If they are not, call a
qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparation of the location and
electrical, tap water and waste water
installations at the place of installation
is under customer's responsibility.
B
Installation and electrical connections
of the product must be carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
A
Prior to installation, visually check if
the product has any defects on it. If
so, do not have it installed. Damaged
products cause risks for your safety.
C
Make sure that the water inlet and
discharge hoses as well as the power
cable are not folded, pinched or
crushed while pushing the product
into its place after installation or
cleaning procedures.
Appropriate installation location
Place the machine on a rigid floor.
Do not place it on a long pile rug or
similar surfaces.
Total weight of the washing machine
and the dryer -with full load- when
they are placed on top of each other
reaches to approx. 180 kilograms.
Place the product on a solid and flat
floor that has sufficient load carrying
capacity!
Do not place the product on the
power cable.
Do not install the product at places
where temperature may fall below
0ºC.
Place the product at least 1 cm away
from the edges of other furniture.
Removing packaging
reinforcement
Tilt the machine backwards to remove
the packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
Removing the
transportation locks
A
Do not remove the transportation
locks before taking out the packaging
reinforcement.
A
Remove the transportation safety
bolts before operating the washing
machine, otherwise, the product will
be damaged.
1. Loosen all the bolts with a spanner
until they rotate freely (C).
2. Remove transportation safety bolts by
turning them gently.
3. Attach the plastic covers supplied in
the User Manual bag into the holes on
the rear panel. (P)
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BEKO WM74135W wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info