Bedienungsanleitung BEKO WMB 91442 (Seite 55 von 68) (Deutsch, Englisch, Holländisch, Französisch)

475973

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Removing the transportation locks

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

Remove the transportation safety bolts before

operatingthewashingmachine,otherwise,the

productwillbedamaged.

1. Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Remove transportation safety bolts by turning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manual bag into the holes on the rear panel. (P)

Keep the transportation safety bolts in a safe

placetoreusewhenthewashingmachineneeds

to be moved again in the future.

 Nevermovetheproductwithoutthe

transportation safety bolts properly fixed in place!

Connecting water supply

 Thewatersupplypressurerequiredtorunthe

productisbetween1to10bars(0.1–10MPa).

Itisnecessarytohave10–80litersofwater

flowingfromthefullyopentapinoneminute

to have your machine run smoothly. Attach a

pressurereducingvalveifwaterpressureis

higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

mustinstallthesuppliedstoppertothehotwater

valve before operating the product. (Applies

fortheproductssuppliedwithablindstopper

group.)

 Ifyouwanttousebothwaterinletsofthe

product,connectthehotwaterhoseafter

removing the stopper and gasket group from

thehotwatervalve.(Appliesfortheproducts

suppliedwithablindstoppergroup.)

 Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

thelaundrywillgetdamagedortheproductwill

switchtoprotectionmodeandwillnotoperate.

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connectthespecialhosessuppliedwiththe

producttothewaterinletsontheproduct.Red

hose(left)(max.90ºC)isforhotwaterinlet,blue

hose(right)(max.25ºC)isforcoldwaterinlet.

 Ensurethatthecoldandhotwaterconnections

aremadecorrectlywheninstallingtheproduct.

Otherwise,yourlaundrywillcomeouthotatthe

endofthewashingprocessandwearout.

2. Tightenallhosenutsbyhand.Neverusea

wrenchwhentighteningthenuts.

3. Open the taps completely after making the

hoseconnectiontocheckforwaterleaksatthe

connectionpoints.Ifanyleaksoccur,turnoff

the tap and remove the nut. Retighten the nut

carefullyaftercheckingtheseal.Topreventwater

leakages and damages caused by them, keep

thetapsclosedwhenthemachineisnotinuse.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connectedtothewastewaterdrainortothe

washbasin.

 Yourhousewillbefloodedifthehosecomesout

ofitshousingduringwaterdischarge.Moreover,

thereisriskofscaldingduetohighwashing

temperatures! To prevent such situations and to

ensuresmoothwaterintakeanddischargeofthe

machine, fix the end of the discharge hose tightly

so that it cannot come out.

• Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

• Incasethehoseiselevatedafterlayingitonthe

floor level or close to the ground (less than 40 cm

abovetheground),waterdischargebecomes

more difficult and the laundry may come out

excessivelywet.Therefore,followtheheights

described in the figure.

• Topreventflowingofdirtywaterbackintothe

machineandtoallowforeasydischarge,do

notimmersethehoseendintothedirtywateror

driveitinthedrainmorethan15cm.Ifitistoo

long, cut it short.

• Theendofthehoseshouldnotbebent,itshould

not be stepped on and the hose must not be

pinchedbetweenthedrainandthemachine.

• Ifthelengthofthehoseistooshort,useitby

adding an original extension hose. Length of the

hose may not be longer than 3.2 m. To avoid

waterleakfailures,theconnectionbetweenthe

extension hose and the drain hose of the product

mustbefittedwellwithanappropriateclampas

not to come off and leak.

BEKO WMB 91442 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info