Bedienungsanleitung BEKO WMP601 (Seite 10 von 36) (Englisch)

556965

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

10 / 36 EN

Washing Machine / User‘s Manual

Installation

3. Attach the plastic covers supplied in the User

Manual bag into the holes on the rear panel. (P)

Keep the transportation safety bolts in

a safe place to reuse when the washing

machine needs to be moved again in the

future.

Never move the product without the

transportation safety bolts properly fixed

in place!

3.4 Connecting water supply

The water supply pressure required to run

the product is between 1 to 10 bars (0.1 –

10 MPa). It is necessary to have 10 – 80

liters of water flowing from the fully open

tap in one minute to have your machine run

smoothly. Attach a pressure reducing valve if

water pressure is higher.

If you are going to use the double water-

inlet product as a single (cold) water-inlet

unit, you must install the supplied stopper

to the hot water valve before operating the

product. (Applies for the products supplied

with a blind stopper group.)

WARNING: Models with a single water

inlet should not be connected to the hot

water tap. In such a case the laundry will

get damaged or the product will switch to

protection mode and will not operate.

WARNING: Do not use old or used water

inlet hoses on the new product. It may cause

stains on your laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose (left) (max. 90 ºC) is for hot water inlet,

blue hose (right) (max. 25 ºC) is for cold water

inlet.

WARNING: Ensure that the cold and hot

water connections are made correctly when

installing the product. Otherwise, your

laundry will come out hot at the end of the

washing process and wear out.

2. Tighten all hose nuts by hand. Never use a tool

when tightening the nuts.

3. Open the taps completely after making the

hose connection to check for water leaks at

the connection points. If any leaks occur, turn

off the tap and remove the nut. Retighten the

nut carefully after checking the seal. To prevent

water leakages and damages caused by them,

keep the taps closed when the machine is not in

use.

3.5 Connecting to the drain

•Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

WARNING: Your house will be flooded

if the hose comes out of its housing

during water discharge. Moreover, there

is risk of scalding due to high washing

temperatures! To prevent such situations

and to ensure smooth water intake and

discharge of the machine, fix the end

of the discharge hose tightly so that it

cannot come out.

•Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

•Incasethehoseiselevatedafterlayingiton

the floor level or close to the ground (less than

40 cm above the ground), water discharge

becomes more difficult and the laundry may

come out excessively wet. Therefore, follow the

heights described in the figure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WMP601 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info