Bedienungsanleitung BEKO WMY 81413 LMB2 (Seite 68 von 81) (Deutsch, Holländisch, Französisch)

676646

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

68 / EN

Washing Machine / User’s Manual

3.AttachtheplasticcoverssuppliedintheUserManualbag

into the holes on the rear panel.

(P)

Keep the transportation safety bolts in a safe place to

reusewhenthewashingmachineneedstobemoved

again in the future.

Nevermovetheproductwithoutthetransportationsafety

boltsproperlyfixedinplace!

2.4 Connecting water supply

Thewatersupplypressurerequiredtoruntheproductis

between1to10bars(0.1–1MPa).Itisnecessaryto

have10–80litersofwaterflowingfromthefullyopen

tap in one minute to have your machine run smoothly.

Attachapressurereducingvalveifwaterpressureis

higher.

Ifyouaregoingtousethedoublewater-inletproduct

as a single

(cold)water-inletunit,youmustinstallthe

suppliedstoppertothehotwatervalvebeforeoperating

theproduct.(Appliesfortheproductssuppliedwitha

blind stopper group.)

WARNING: Modelswithasinglewaterinletshouldnot

beconnectedtothehotwatertap.Insuchacasethe

laundrywillgetdamagedortheproductwillswitchto

protectionmodeandwillnotoperate.

WARNING: Donotuseoldorusedwaterinlethoses

onthenewproduct.Itmaycausestainsonyourlaundry.

1.Connectthespecialhosessuppliedwiththeproductto

thewaterinletsontheproduct.Redhose(left)(max.90

ºC)isforhotwaterinlet,bluehose(right)(max.25ºC)is

forcoldwaterinlet.

WARNING: Ensurethatthecoldandhotwater

connectionsaremadecorrectlywheninstallingthe

product.Otherwise,yourlaundrywillcomeouthotatthe

endofthewashingprocessandwearout.

2.Tightenallhosenutsbyhand.Neveruseatoolwhen

tightening the nuts.

3. Open the taps completely after making the hose

connectiontocheckforwaterleaksattheconnection

points.Ifanyleaksoccur,turnoffthetapandremovethe

nut.Retightenthenutcarefullyaftercheckingtheseal.To

preventwaterleakagesanddamagescausedbythem,

keepthetapsclosedwhenthemachineisnotinuse.

2.5 Connecting to the drain

• Theendofthedrainhosemustbedirectlyconnectedto

thewastewaterdrainortothewashbasin.

WARNING: Yourhousewillbefloodedifthehose

comesoutofitshousingduringwaterdischarge.

Moreover,thereisriskofscaldingduetohighwashing

temperatures!Topreventsuchsituationsandtoensure

smoothwaterintakeanddischargeofthemachine,fix

the end of the discharge hose tightly so that it cannot

come out.

• Thehoseshouldbeattachedtoaheightofatleast40

cm, and 100 cm at most.

• Incasethehoseiselevatedafterlayingitonthefloor

level or close to the ground (less than 40 cm above the

ground),waterdischargebecomesmoredifficultandthe

laundrymaycomeoutexcessivelywet.Therefore,follow

the heights described in the figure.

100cm

40cm

• Topreventflowingofdirtywaterbackintothemachine

andtoallowforeasydischarge,donotimmersethehose

endintothedirtywaterordonotdriveitinthedrainmore

than15cm.Ifitistoolong,cutitshort.

• Theendofthehoseshouldnotbebent,itshouldnotbe

steppedonandthehosemustnotbepinchedbetween

the drain and the machine.

• Ifthelengthofthehoseistooshort,useitbyadding

anoriginalextensionhose.Lengthofthehosemay

notbelongerthan3.2m.Toavoidwaterleakfailures,

theconnectionbetweentheextensionhoseandthe

drainhoseoftheproductmustbefittedwellwithan

appropriate clamp as not to come off and leak.

2.6 Adjusting the feet

WARNING: Inordertoensurethattheproduct

operates more silently and vibration-free, it must stand

levelandbalancedonitsfeet.Balancethemachine

byadjustingthefeet.Otherwise,theproductmay

move from its place and cause crushing and vibration

problems.

1. Loosen the lock nuts on the feet by hand.

2.Adjustthefeetuntiltheproductstandsleveland

balanced.

3.Tightenalllocknutsagainbyhand.

BEKO WMY 81413 LMB2 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info