Bedienungsanleitung BEKO WTL104151 (Seite 9 von 32) (Englisch)

758310

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

9 / EN Washing Machine / User’s Manual

4.1.7 Electrical connection

Connect the product to a grounded outlet

protected by a 13 A fuse. Our company shall

not be liable for any damages that will arise

when the product is used without grounding in

accordance with the local regulations.

• Connection must comply with national

regulations.

• The wiring for the electrical outlet circuit

must be sufficient to meet the appliance

requirements. Use of a Groud Fault Circuit

Interrupter (GFCI) is recommended.

• Power cable plug must be within easy reach

after installation.

• If the current value of the fuse or breaker

in the house is less than 13 Amps, have a

qualified electrician install a 13 Amp fuse.

• The voltage specified in the “Technical

specifications” section must be equal to

your mains voltage.

• Do not make connections via extension

cables or multi-plugs.

CAUTION!

• Damaged power cables must be replaced

by the Authorised Service Agents.

Electrical requirements

Before you insert the plug into the wall socket

make sure that the voltage and the frequency

shown in the rating label corresponds to your

electricity supply.

We recommend that this appliance be

connected to the mains supply via a suitable

switched and fused socket in a readily

accessible position.

Should the mains lead of the appliance

become damaged or need replacing at any

time, it must be replaced by a special purpose

made mains lead which can only be obtained

from a Authorised Service Agent.

WARNING!

• This appliance must be earthed

If the fitted moulded plug is not suitable for

your socket, then the plug should be cut off

and an appropriate plug fitted.

Destroy the old plug, which is cut off as a

plug with a bared cord could cause a shock

hazard if inserted into a socket elsewhere in

the house.

The moulded plug on this appliance

incorporates a 13A fuse. Should the fuse need

to be replaced an ASTA approved BS1362

fuse of the same rating must be used. Do not

forget to refit the fuse cover. In the event of

losing the fuse cover, the plug must not be

used until a replacement fuse cover has been

fitted. Colour of the replacement fuse cover

must be the same colour as that visible on the

pin face of the plug. Fuse covers are available

from any good electrical store.

Important

Fitting a different plug

As the colours of the

wires in the mains

lead of this appliance

may not correspond

with the coloured

markings identifying

the terminals on your

plug, proceed as

follows:

1 Connect the green - yellow or green (earth)

wire to the terminal in the plug marked ‘E’

or with the symbol f or coloured green and

yellow or green.

Connect the blue (neutral) wire to the terminal

in the plug marked ‘N’ or coloured black.

3 Connect the brown (live) wire to the terminal

in the plug marked ‘L’ or coloured red.

With the alternative plugs a 13A fuse must be

fitted either in the plug or adaptor or in the main

fuse box. If in doubt contact a qualified electrician.

Transportation of the product

1. Unplug the product before transporting it.

2. Remove water drain and water supply

connections.

3. Drain all water that has remained in the

product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WTL104151 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info