Bedienungsanleitung BEKO WTV8716XWWST (Seite 8 von 36) (Englisch)

815662

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

8 / EN Washing Machine / User’s Manual

ACAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be

damaged.

CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the

future.

Install the transport safety bolts in reverse order of the disassembly procedure.

Never move the product without the transportation safety bolts properly fixed in place!

4.1.4 Connecting water supply

It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run

smoothly. Attach a pressure reducing valve if water pressure is higher.

ACAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will

get damaged or the product will switch to protection mode and will not operate.

1 Tighten the nuts of the hose by hand. Never use a tool when

tightening the nuts.

2 When hose connection is completed, check whether there is leak

problems at the connection points by opening the taps fully. If any

leaks occur, turn off the tap and remove the nut. Retighten the nut

carefully after checking the seal. In order to prevent the water leaks

and resultant damages, keep the taps closed when you do not use

the product.

4.1.5 Connecting the drain hose to the drain

• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.

ACAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there

is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine

performs water intake and discharge processes without any problem, fix the drain hose securely.

40 cm

100 cm

• Connect the drain hose to a minimum height of 40 cm

and a maximum height of 100 cm.

• In case the drain hose is elevated after laying it on the

floor level or close to the ground (less than 40 cm above

the ground), water discharge becomes more difficult and

the laundry may come out excessively wet. Therefore,

follow the heights described in the figure.

• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse

the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too

long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched

between the drain and the machine.

• If the length of the hose is too short, use it by adding an original extension hose. The overall length of the

hose shall not be longer than 3.2 m. To avoid water leak failures, the connection between the extension

hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off

and leak.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WTV8716XWWST Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO WTV8716XWWST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info