Bedienungsanleitung BEKO WTV8741BSCDOS1 (Seite 31 von 83) (Deutsch, Englisch)

757592

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

31 / EN

Washing Machine / User’s Manual

1. Close the taps.

2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them

with an appropriate brush. If the filters are too dirty, remove them from their places with a pliers and

clean in this way.

3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean

thoroughly under running water.

4. Replace the gaskets and filters carefully and tighten their nuts by hand.

4.4.5 Draining remaining water and cleaning the pump filter

The filter system in your product prevents solid items such as buttons, coins and fabric fibers clogging the

pump impeller during draining of washing water. Thus, the water will be drained without any problem and the

service life of the pump will extend.

If the product fails to drain water inside it, the pump filter is clogged. Filter must be cleaned whenever it is

clogged or in every 3 months. Water must be drained off first to clean the pump filter.

In addition, prior to transporting the product (e.g., when moving to another house) water should be drained

completely.

AWARNING: Foreign substances left in the pump filter may damage your product or may cause noise problem.

WARNING: In regions where freezing is possible, the tap must be closed, system hose must be removed and the water

inside the product must be drained when the product is not in use.

WARNING: After each use, turn off the tap to which the mains hose is connected.

In order to clean the dirty filter and drain the water:

1 Unplug the product to cut off the supply power.

AWARNING: Temperature of the water inside the product may rise up to 90 ºC. To avoid the risk of scalding, clean the

filter after the water inside the product is cooled down.

2 Open the filter cover.

3 Follow the below procedures in order to drain water.

If the product has an emergency water draining hose, in order to drain the water:

a Pull the emergency draining hose out from its

seat.

b Place a large container at the end of the hose.

Drain the water into the container by pulling

out the plug at the end of the hose. When the

container is full, block the inlet of the hose

by replacing the plug. After the container is

emptied, repeat the above procedure to drain the

water in the product completely.

c When draining of water is finished, close the end

by the plug again and fix the hose in its place.

d Turn and remove the pump filter.

4 Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.

5. Replace the filter.

6. If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat

the tabs in the lower part into their places first, and then press the upper part to close.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WTV8741BSCDOS1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO WTV8741BSCDOS1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info