Bedienungsanleitung Beldray BEL0207 (Seite 5 von 10) (Englisch)

777020

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

THE SCIENCE

BEHIND CLEAN

Instructions for Use

Ensure that the Steam Station is unplugged from the mains power supply.

Remove the water tank from the Steam Station main body by grasping the water ﬁll entrance

and gently but ﬁrmly pulling it out. Fill the water tank with tap water up to the Max. level marked

on the front of the tank. Once full, replace the water tank back onto the Steam Station main

body until it clicks into position.

Connect the Steam Station to the mains power supply.

To begin using the Steam Station, press the ‘On/Off’ switch. The power indicator light will ﬂash

to indicate that the boiler is heating up.

Select the temperature of the Steam Station by turning the temperature control dial on the iron

to the desired heat setting.

When the Steam Station has reached the correct temperature, the power indicator light will

stop ﬂashing and will remain lit; when the heat ready indicator light turns off, the Steam Station is

ready for use.

If the low water level indicator light ﬂashes and an audible noise is emitted, the water level in the

tank is too low and the water tank will need reﬁlling according to the instructions provided.

Note: It is possible to ﬁll the water tank whilst it is still attached to the Steam Station main unit

by directly pouring water into the water ﬁll entrance.

Note: This Steam Station is designed for use with tap water. If the water in your area is

particularly hard, please use demineralised water to protect the internal parts of the Steam

Station from limescale build-up.

Note: If the temperature required for a particular garment is not speciﬁed, it is recommended

to iron at the lowest heat setting and then increase if necessary, in order to avoid damage to

the material.

Tip: Before use, separate the clothes to be ironed by ironing temperature, starting at the coolest

setting, as the iron will heat up faster than it will cool down.

Steam Ironing

When steam ironing for the ﬁrst time, it is recommended to iron a plain cloth to test that the

iron is working at the correct temperature.

To use the steam setting, press the trigger/steam button on the underside of the iron handle.

This will provide steam up until the button is released. The continuous steam jet button can be

locked down in order to provide continuous steam by sliding the steam button lock towards the

rear of the iron.

Vertical Steam Ironing

Vertical steam ironing is especially useful when removing creases from hanging fabrics, such as

curtains, wall hangings and certain clothes.

To use the vertical steam function, hold the iron approximately 1–2 cm away from the fabric to

be steamed, and then press and hold the steam button on the underside of the iron handle and

direct the iron soleplate at the area to be steamed.

BEL0207 Steam Station 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beldray BEL0207 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info