Bedienungsanleitung Bellelli B-One Standard (Seite 8 von 86) (Alle Sprachen)

772323

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

(e.g. on a car roof, on a towed trailer or behind a motorhome).

Periodically check the bike: tyres, brakes, lights, etc.

Periodically wash the child seat with soap and water. Do not use aggressive substances.

MOUNTING THE CHILD SEAT

!!! Do not carry out mounting operations with the child in the seat.

Make sure you have all the components before proceeding with assembly (g. A).

Mounting the support bracket

Take the back rack off the bike if it interferes with mounting the seat.

Mount the support bracket on the bicycle frame as illustrated in g. B. Make sure that the arrows printed

on the front side of the block are pointing upwards.

!!! WARNING: mount the brace on the bicycle frame and not on the pipe under the bicycle saddle.

!!! WARNING: check that the brake and gear cables do not interfere with the bracket (1).

Choose the best screws (6) for your frame (see Table 1). (If the screws that come with the seat are too

short, longer ones [M6x80, for instance] can be found in a hardware store).

Slip the screws (6) into their holes.

Tighten the nuts slightly and evenly (7) (g. C).

The support bracket must be free to slide along the tube: it will be tightened once the seat is in the

correct position (see xing the child seat to the bike).

Fixing the support fork to the child seat

Turn the seat over.

Position the U-bend of the support fork (9) under the ap (g. D). Place the tool in its slot.

Line up the hole on the welded post (9) with the hole in the seat.

Slip the bolt (11) through the plate (10), the holes in the child seat, and the welded bracket (g. E).

Fully tighten the nut (12) (g. F).

Fixing the child seat to the bike

Hold down the yellow button on the bracket (2). Insert the support fork (8) into the upper part of the

bracket (1) (g. G).

!!! WARNING: once inserted, make sure that the yellow button pops out (2). If it doesn’t the fork

(8) is not inserted correctly: repeat the operation.

Check that the child seat does not interfere with pedals, brakes, gears and other moving parts on the bike.

Leave enough room for the child’s legs.

Line the child seat up with the bike’s axis.

Fully tighten the screws (6) on the bracket after having found the best position for the seat.

!!! WARNING: periodically check that the screws are tight. They may loosen with use.

Taking the child seat off the bike

Hold down the yellow button (2) on the bracket and pull up the support fork (8) up and off (g. G).

Installing the foot rests

Take the left foot rest (13) (marked SX on the back).

Push it into the vertical slot on the left leg.

Push up as far as possible (g. H).

Take the blocking lever (15) for the left foot rest (marked SX on the back).

Push the blocking lever into the hole behind the rest. Insert from the outside and push right in (g. I).

Close the blocking lever by pushing downwards until you hear a click (g. L).

Repeat the same operations for the right foot rest (marked DX).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bellelli B-One Standard Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info