Bedienungsanleitung Belling 1000-AWBL (Seite 13 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

659750

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 13 -

by 3A fuse.

2. Warning!

In certain circumstances electrical appliances may be a

danger hazard.

A) Do not check the status of the filters while the cooker

hood is operating.

B) Do not touch bulbs or adjacent areas, during or straight

after prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker

hood.

D) Avoid free flame, as it is damaging for the filters and a

fire hazard.

E) Constantly check food frying to avoid that the over-

heated oil may become a fire hazard.

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance is not intended for use by young children

or infirm persons without supervision.

H) Young children should be supervised to ensure they do

not play with the appliance.

I) There shall be adequate ventilation of the room when

the rangehood is used at the same time as appliances

burning gas or other fuels.

L) There is a risk of fire if cleaning is not carried out in

accordance with the instructions.

This appliance conforms to the European Directive EC/2002/96,

Waste Electrical and Electronic Equipment (WEEE). By making

sure that this appliance is disposed of in a suitable manner, the

user is helping to prevent potential damage to the environ-

ment or to public health.

The symbol on the product or on the accompanying

paperwork indicates that the appliance should not be

treated as domestic waste, but should be delivered to

a suitable electric and electronic appliance recycling collection

point. Follow local guidelines when disposing of waste. For

more information on the treatment, re-use and recycling of

this product, please contact your local authority, domestic

waste collection service or the shop where the appliance was

purchased.

INSTALLATION INSTRUCTIONS

•Assemblyandelectricalconnectionsmustbecarriedout

by specialised personnel.

•Wearprotectiveglovesbeforeproceedingwiththe

installation.

•ElectricConnection:

Note! Verify the data label placed inside the appliance:

- If the symbol

appears on the plate, it means that no earth

connection must be made on the appliance, therefore follow

the instructions concerning insulation class II.

- If the symbol

DOES NOT appear on the plate, follow the

instructions concerning insulation class I.

Insulation class II

- The appliance has been manufactured as a class II, therefore

no earth cable is necessary. The plug must be easily accessible

after the installation of the appliance. If the appliance is equip-

ped with power cord without plug, a suitably dimensioned

omnipolar switch with 3 mm minimum opening between con-

tacts must be fitted between the appliance and the electricity

supply in compliance with the load and current regulations.

- The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral.

Insulation class I

This is a class I, appliance and must therefore be connected to

an effiecient earthing system.

- The appliance must be connected to the electricity supply as

follows:

BROWN = L line

BLUE = N neutral

YELLOW/GREEN =

earth.

The neutral wire must be connected to the terminal with the

N symbol while the YELLOW/GREEN, wire must be connected

to the terminal by the earth symbol

When connecting the appliance to the electricity supply, make

sure that the mains socket has an earth connection. After fitting

the ducted cooker hood, make sure that the electrical plug is

in a position where it can be accessed easily. If the appliance

is connected directly to the electricity supply, an omnipolar

switch with a minimum contact opening of 3 mm must be

placed in between the two; its size must be suitable for the

load required and it must comply with current legislation.

•  If the hob is electric, gas, or induction, the minimum distance

between the same and the lower part of the hood must be at

least 65 cm. If a connection tube composed of two parts is

used, the upper part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same con-

ductor used to circulate hot air or for evacuating fumes from

other appliances generated by other than an electrical source.

Before proceeding with the assembly operations, remove the

anti-grease filter(s) (Fig.5) so that the unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•  We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with a

smaller diameter is used, the efficiency of the product may be

reduced and its operation may become noisier.

•  If your appliance has been designed for use in habitations

supplied with acentralised suction device perform the fol-

lowing operations:

- The switch controls opening and closure of a valve using

a thermoelectical device. By placing the switch in the ON

position, after a minute, the valve opens rotating 90° allowing

suction of the stale air. By placing the switch in the OFF posi-

tion, the valve closes after 100 seconds.

•Fixingtothewall:

Drill the holes A respecting the distances indicated (Fig.2). Fix

the appliance to the wall and align it in horizontal position

to the wall units. When the appliance has been adjusted,

definitely fix the hood using the screws A (Fig.4). For the

various installations use screws and screw anchors suited to

the type of wall (e.g. reinforced concrete, plasterboard, etc.). If

the screws and screw anchors are provided with the product,

check that they are suitable for the type of wall on which the

hood is to be fixed.

•Fixingthedecorativetelescopicflue:

Arrange the electrical power supply within the dimensions of

the decorative flue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening. Adjust the width of the support bra-

cket of the upper flue (Fig.3). Then fix it to the ceiling using the

screws A (Fig.3) in such a way that it is in line with your hood

and respecting the distance from the ceiling indicated in Fig.2.

Connect the flange C to the air exhaust hole using a connection

pipe (Fig.4). Insert the upper flue into the lower flue and rest

Belling 1000-AWBL Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info