Bedienungsanleitung Bellman BE1210 (Seite 8 von 13) (Englisch)

747165

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

13 14



If the alarm still indicates a yellow blink with a single beep, the batteries may be depleted.

Replace them with fresh batteries.



If the red, yellow and green LEDs do not blink in sequence, the batteries may be installed

incorrectly (reverse polarity). Remove the alarm from the mounting bracket, remove the

battery cover and check if the batteries are installed correctly.



If the batteries were connected incorrectly, and after correcting the polarity of the batteries,

for the rst hour, the alarm may indicate CO is present by a blinking red LED. Please note

that during this period, the alarm will still activate as required during an actual CO event.

Warning! Exposures to high or low temperatures or high humidity may reduce battery life.

Use only batteries specied in marking. Use of a dierent battery may have a detrimental

eect on alarm operation.

Functional gas test

The alarm checks for CO gas every 4 seconds

and when exposed to the gas, the red LED will

blink to conrm that it is detecting the gas.

Solo C6 brand canned CO testing agent may

be used to verify the alarm’s ability to sense

CO. To gas test the alarm, spray the canned

CO within 1/4" of the gas entry holes for 3 s,

see Overview. Within seconds, the red LED

will begin to blink to conrm that the alarm

has detected the CO.

To return the unit to standby, simply leave

the alarm in clean air for a few minutes until

the red light is no longer blinking.

Figure 4

Battery replacement

What to do when the alarm sounds

Warning! Actuation of your CO alarm indicates the presence of carbon monoxide (CO)

which can KILL YOU. If an alarm signal sound:

1 Operate reset/silence button (only operational at concentrations <250ppm).

2 Call your local re department or 911.

3 Immediately move to fresh air, outdoors or by an open door/ window. Do a head count to en-

sure that all persons are accounted for. DO NOT re-enter the premises until the rst responders

have arrived, the premises have been aired out and your alarm returns to its normal condition.

4 After following steps 1–3, if your alarm reactivates within a 24 hour period, repeat steps 1–3

and call a qualied appliance technician to investigate for sources of CO from fuel burning

equipment and appliances, and inspect for proper operation of this equipment. If problems

are identied during this inspection have the equipment serviced immediately. Note any

combustion equipment not inspected by the technician and consult the manufactures’

instructions, or contact the manufacturers directly, for more information about CO safety

and this equipment. Make sure that motor vehicles are not, and have not been, operating in

an attached garage or adjacent to the residence.

Note: When ventilation is provided by leaving the window and doors open, the CO build up

may have dissipated by the time help arrives and the alarm may have stopped sounding.

Although your problem may appear temporarily solved, it is crucial that the source of the

CO is determined and appropriate repairs made.

How to protect your family

Follow these guidelines to reduce the risk of carbon monoxide poisoning.

1 Know and look out for warning signs that carbon monoxide may be present. These include:



The CO alarm warning of abnormal levels.



Staining, soot marks or discoloration on or around appliances.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bellman BE1210 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info